manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

10B-28 Body Electrical Control System: 

Troubleshooting

Step

Action

Yes

No

1

Check DTC in BCM

Is DTC U1100 (No. 1100) and DTC U1073 (No. 1073) 
detected together?

Go to “DTC U1073 (No. 
1073): Control Module 
Communication Bus 
Off: ”.

Go to Step 2.

2

Check DTC in ECM

1) Check ECM for DTC.

Is DTC P1678 detected?

Go to “DTC P1674: 
CAN Communication 
(Bus Off Error):  in 
Section 1A”.

Go to Step 3.

3

Check each control module connectors

1) Check connection of connectors of all control modules 

communicating by means of CAN.

2) Recheck BCM for DTC.

Is DTC U1100 (No. 1100) detected?

Go to Step 4.

Intermittent trouble. 
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.

4

CAN communication circuit check

1) Turn ignition switch to OFF position.
2) Disconnect connectors of all control modules 

communicating by means of CAN.

3) Check CAN communication circuit between control 

modules for open, short and high resistance.

Is each CAN communication circuit in good condition?

Go to Step 5.

Repair circuit.

5

Check DTC in TCM

1) Connect connectors to all control modules.
2) Check TCM for DTC.

Is DTC P1777 detected?

Check ECM power and 
ground circuit. If circuit 
is OK, substitute a 
known-good ECM and 
recheck.

Substitute a known-
good BCM (included in 
junction block assembly 
and recheck.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
UnderCover 2110 Installation Manual preview
2110
Бренд: UnderCover Страницы: 16
Jeep Renegade Owner'S Handbook Manual preview
Renegade
Бренд: Jeep Страницы: 212
RAM 2500 2020 Quick Reference Manual preview
2500 2020
Бренд: RAM Страницы: 20
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
ZAPTEC ZapCharger Portable C1 User Manual preview
ZapCharger Portable C1
Бренд: ZAPTEC Страницы: 20
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Бренд: Whispbar Страницы: 63
Thule 953000 Instructions Manual preview
953000
Бренд: Thule Страницы: 8
Curt Manufacturing 58963 Installation Manual preview
58963
Бренд: Curt Manufacturing Страницы: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Бренд: Whispbar Страницы: 112
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Бренд: FALCON RIDGE Страницы: 6
Lund Tonno Pro Installation Instructions Manual preview
Tonno Pro
Бренд: Lund Страницы: 12
Hama MagLock Vent Operating Instructions Manual preview
MagLock Vent
Бренд: Hama Страницы: 39
Volvo 2009 S40 Owner'S Manual preview
2009 S40
Бренд: Volvo Страницы: 286
MovaNext Bike adapter 3 Assembly Instructions preview
Bike adapter 3
Бренд: MovaNext Страницы: 4
Valeo MBHL Operating Manual preview
MBHL
Бренд: Valeo Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды