manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1H-9 Ignition System: 

Ignition Coil Assembly (Including ignitor) 
Inspection

S4RS0A1806006

Measure secondary coil for resistance.
If resistance is out of specification, replace ignition coil 
assembly.

Secondary coil resistance
7.6 – 10.2 k

:

 at 20 

q

C, 68 

q

F

Ignition Timing Inspection

S4RS0A1806007

NOTE:

• Ignition timing is not adjustable. If ignition 

timing is out of specification, check 
system related parts.

• Before starting engine, place transmission 

gear shift lever in “Neutral” (shift selector 
lever to “P” range for A/T model), and set 
parking brake.

 

1) Connect scan tool to DLC (1) with ignition switch 

OFF.

Special tool
(A):  SUZUKI scan tool

2) Start engine and warm it up to normal operating 

temperature.

3) Make sure that all of electrical loads except ignition 

are switched off.

4) Check to be sure that idle speed is within 

specification referring to “Idle Speed / Idle Air Control 
(IAC) Duty Inspection:  in Section 1A”.

5) Fix ignition timing by using “Fixed Spark” of “Misc 

Test” mode on scan tool.

6) Set timing light (1) to high-tension cord for No.1 

cylinder and check that ignition timing is within 
specification.

Initial ignition timing (fixed with SUZUKI scan 
tool)
5 

r

 3

q

 BTDC (at specified idle speed)

Ignition order
1 – 3 – 4 – 2

Special tool
(A):  09930–76420

7) If ignition timing is out of specification, check the 

followings.
• CKP sensor
• CKP sensor plate
• TP sensor
• CMP sensor
• CMP sensor rotor tooth of camshaft
• VSS
• Timing chain cover installation

8) After checking initial ignition timing, release ignition 

timing fixation by using scan tool.

9) With engine idling (throttle opening at closed position 

and vehicle stopped), check that ignition timing is 
about 3

q

 – 13

q

 BTDC. (Constant variation within a 

few degrees from 3

q

 – 13

q

 indicates no abnormality 

but proves operation of electronic timing control 
system.) Also, check that increasing engine speed 
advances ignition timing.
If the check results are not satisfactory, check CKP 
sensor and ECM.

I2RH0B180007-

(A)

1

I4RS0A180005-

1, (A)

10

0

I3RB0A180004-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Saab B205 Installation Instructions Manual preview
B205
Бренд: Saab Страницы: 10
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Бренд: Jacob Jensen Страницы: 2
Yakima K1005 Instructions Manual preview
K1005
Бренд: Yakima Страницы: 12
Wagan 2227-1 User Manual preview
2227-1
Бренд: Wagan Страницы: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Бренд: Thermo King Страницы: 2
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Бренд: Brodit Страницы: 2
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
Caraudio-Systems v.LOGiC Intelligent Solution V5-NTG46 Manual preview
v.LOGiC Intelligent Solution V5-NTG46
Бренд: Caraudio-Systems Страницы: 18
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Бренд: Menabo Страницы: 8
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Бренд: Cadillac Страницы: 407
Toyota Sienna 2021 Manual preview
Sienna 2021
Бренд: Toyota Страницы: 600
Subaru 1994 Impreza Supplemental Service Manual preview
1994 Impreza
Бренд: Subaru Страницы: 540
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Бренд: Alphasonik Страницы: 8
newmotion Dynamic Power Management Home - Module Installation Instruction preview
Dynamic Power Management Home - Module
Бренд: newmotion Страницы: 20
Thule 145012 Quick Start Manual preview
145012
Бренд: Thule Страницы: 2
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Бренд: Rugged Ridge Страницы: 5
Connects2 CTUPO01 Quick Start Manual preview
CTUPO01
Бренд: Connects2 Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды