manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Instrumentation / Driver Info. / Horn:  9C-4

Diagnostic Information and Procedures

Speedometer and VSS Symptom Diagnosis

S4RS0A9304001

NOTE:
Make sure that any DTC is not detected by both ECM and TCM before starting the troubleshooting by 
using the following table. If any DTC is detected, troubleshoot the DTC advance.

 

Tacho meter Symptom Diagnosis

S4RS0A9304015

NOTE:
Make sure that any DTC is not detected by ECM before starting the troubleshooting by using the 
following table. If any DTC is detected, troubleshoot the DTC advance.

 

Engine Coolant Temperature (ECT) Meter Symptom Diagnosis

S4RS0A9304016

NOTE:
Make sure that any DTC is not detected by ECM before starting the troubleshooting by using the 
following table. If any DTC is detected, troubleshoot the DTC advance.

 

Fuel Meter Symptom Diagnosis

S4RS0A9304017

NOTE:
Make sure that any DTC is not detected by ECM before starting the troubleshooting by using the 
following table. If any DTC is detected, troubleshoot the DTC advance.

 

Condition

Possible cause

Correction / Reference Item

Speedometer shows no 
operation or incorrect 
operation

Circuit fuse blown

Replace fuse and check for short circuit.

VSS faulty (M/T vehicle)

Check VSS referring to “Vehicle Speed Sensor 
(VSS) Inspection (M/T model):  in Section 1C”.

Output shaft speed sensor / VSS faulty 
(A/T vehicle)

Check output shaft speed sensor / VSS 
referring to “Output Shaft Speed Sensor (VSS) 
Inspection:  in Section 5A”.

Wiring or ground faulty

Repair circuit.

Combination meter faulty 

Replace combination meter.

Condition

Possible cause

Correction / Reference Item

Tacho meter shows no 
operation or incorrect 
operation

Circuit fuse blown

Replace fuse and check for short circuit.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Condition

Possible cause

Correction / Reference Item

Engine coolant 
temperature (ECT) meter 
shows no operation or 
incorrect operation

Circuit fuse blown

Replace fuse and check for short circuit.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Condition

Possible cause

Correction / Reference Item

Fuel meter shows no 
operation or incorrect 
operation

Circuit fuse blown

Replace fuse and check for short circuit.

Fuel level sensor faulty

Check fuel level sensor referring to “Fuel Level 
Sensor Inspection: ”.

Wiring or ground faulty

Repair circuit.

Combination meter faulty

Replace combination meter.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

JANE MICRO Quick Start Manual preview
MICRO
Бренд: JANE Страницы: 6
RAM Ram 3500 2012 User Manual preview
Ram 3500 2012
Бренд: RAM Страницы: 116
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Бренд: Safe Fleet Страницы: 12
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Бренд: Mazda Страницы: 400
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Бренд: Safe Fleet Страницы: 11
Camec 042374 User Manual preview
042374
Бренд: Camec Страницы: 19
PEUGEOT 407 2010 Manual preview
407 2010
Бренд: PEUGEOT Страницы: 249
AC Schnitzer DKG Fitting Instructions Manual preview
DKG
Бренд: AC Schnitzer Страницы: 16
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
Jaeger 21360508 Fitting Instructions Manual preview
21360508
Бренд: Jaeger Страницы: 13
cam PFF Series Operating Manual preview
PFF Series
Бренд: cam Страницы: 28
BraunAbility Rampvan Maintenance And Service Manual preview
Rampvan
Бренд: BraunAbility Страницы: 46
PUTCO 1951 Series Instruction Manual preview
1951 Series
Бренд: PUTCO Страницы: 3
Magneti Marelli Obd Road User Manual preview
Obd Road
Бренд: Magneti Marelli Страницы: 9
Pet Gear TL9000 Instruction Manual preview
TL9000
Бренд: Pet Gear Страницы: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Бренд: Suzuki Страницы: 570
Metra Electronics 95-7617B Installation Instructions Manual preview
95-7617B
Бренд: Metra Electronics Страницы: 8
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Бренд: Mazda Страницы: 604

Бренды по названию

Популярные бренды

Загрузить еще бренды