manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Hood / Fenders / Doors:  9J-5

Rear Door Assembly Removal and Installation

S4RS0A9A06008

Refer to “Front Door Assembly Removal and Installation: ” as removal and installation procedures are basically the 
same. However, note the following.
• Tighten rear door hinge bolts and nuts to specified torque referring to “Rear Door Assembly Components”.

Rear End Door Assembly Components

S4RS0A9A06009

Rear End Door Assembly Removal and 
Installation

S4RS0A9A06010

Removal

1) Remove rear end door trim (1).
2) Remove related section of head lining and rear trim.
3) Disconnect rear end door harness couplers (2) and 

washer hose (3).

4) Remove rear end door balancers (4).
5) Remove door hinge nuts (5) and remove rear end 

door assembly (6).

3

(a)

(a)

1

2

4

6

5

I4RS0A9A0010-

1. Rear end door panel assembly

4. Rear end door balancer

: 23 N

˜

m (2.3 kg-m, 17.0 lb-ft)

2. Rear end door window glass

5. Rear end door trim

 

 3. Rear end door hinge

: Apply lithium grease 99000-25010 to door hinge 
moving section.
: Apply sealant 99000-31110 to contact face.

6. Rear end door opening wether-strip

“A”

“B”

“B”

“A”

“B”

“A”

“A”

“A”

“A”

“A”

“A”

“A”

1

6

5

4

2

3

2

4

I4RS0A9A0011-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Бренд: Cadillac Страницы: 24
Cadillac Escalade Personalization Manual preview
Escalade
Бренд: Cadillac Страницы: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Бренд: Cadillac Страницы: 20
Triumph MAYFLOWER 1951 Instruction Book preview
MAYFLOWER 1951
Бренд: Triumph Страницы: 86
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Бренд: Safe Fleet Страницы: 38
Kargo Master 4A82T Installation Manual preview
4A82T
Бренд: Kargo Master Страницы: 6
AA Products RB0007 Instruction Manual preview
RB0007
Бренд: AA Products Страницы: 6
Bestop Bikini Installation Instructions preview
Bikini
Бренд: Bestop Страницы: 5
PowerMadd Tri-mount Installation Instructions preview
Tri-mount
Бренд: PowerMadd Страницы: 3
Improved Racing E5G-601 Instructions Manual preview
E5G-601
Бренд: Improved Racing Страницы: 17
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Бренд: Black+Decker Страницы: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Бренд: Beeper Страницы: 20
Mercedes-Benz 2007 SLR Mclaren Operator'S Manual preview
2007 SLR Mclaren
Бренд: Mercedes-Benz Страницы: 425
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Бренд: Jaeger Страницы: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Бренд: ATS Страницы: 12
Toyota Tacoma 05 Brochure & Specs preview
Tacoma 05
Бренд: Toyota Страницы: 26
Hama MagLock Vent Operating Instructions Manual preview
MagLock Vent
Бренд: Hama Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды