manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9C-13 Instrumentation / Driver Info. / Horn: 

Parking Brake Switch Inspection

S4RS0A9306012

Check for continuity between parking brake switch 
terminal and body ground as shown in figure. If found 
defective, replace switch.

Parking brake switch specification
OFF position (parking brake released): No continuity
ON position (parking brake lever pulled up): 
Continuity

Door Switch (Front / Rear Door) Inspection

S4RS0A9306013

Remove door switch from body and check switch for 
continuity. If found defective, replace switch.

Door switch (front / rear door) specification
OFF position (Door closed): No continuity
ON position (Door open): Continuity

Rear End Door Switch Inspection

S4RS0A9306014

Check for continuity between terminal “a” and “b” shown 
in the following.
If check result is not as specified, replace switch.

Rear end door switch specification
Rear end door closed: No continuity
Rear end door opened: Continuity

Outside Air Temperature Sensor Removal and 
Installation

S4RS0A9306016

Removal

1) Disconnect negative (–) cable at battery.
2) Remove front bumper referring to “Front Bumper 

and Rear Bumper Components:  in Section 9K”.

3) Disconnect connector from outside air temperature 

sensor.

4) Remove outside air temperature sensor (1) from 

front bumper member.

Installation

Reverse removal procedure for installation.

1. Parking brake switch
2. Parking brake lever

1

2

I4RS0A930014-

I3RH0A930004-

a

b

I4RS0A930015-

1

I4RS0A930016-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Warrior Products 10936 Installation Instructions preview
10936
Бренд: Warrior Products Страницы: 3
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Бренд: Subaru Страницы: 99
Thule 1308 Instructions Manual preview
1308
Бренд: Thule Страницы: 8
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
Meta System 900000358 Installation Technical Sheet preview
900000358
Бренд: Meta System Страницы: 22
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Bestop Bikini Installation Instructions preview
Bikini
Бренд: Bestop Страницы: 5
PowerMadd Tri-mount Installation Instructions preview
Tri-mount
Бренд: PowerMadd Страницы: 3
Softride 26428 Instructions preview
26428
Бренд: Softride Страницы: 4
Prorack K947 Fitting Instructions Manual preview
K947
Бренд: Prorack Страницы: 14
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Бренд: Ford Страницы: 8
Waeco MAGIC WATCH MWE-850-4XXL Installation And Operating Manual preview
MAGIC WATCH MWE-850-4XXL
Бренд: Waeco Страницы: 228
Lincoln 2012 MKX Owner'S Manual preview
2012 MKX
Бренд: Lincoln Страницы: 364
Hamron 012463 Operating Instructions Manual preview
012463
Бренд: Hamron Страницы: 6
Ranger design C24-DL Installation Manual preview
C24-DL
Бренд: Ranger design Страницы: 14
Rhino-Rack RBC044 Installation Instructions preview
RBC044
Бренд: Rhino-Rack Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды