manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-109

3) Tighten drive plate to torque converter bolts. Align 

bolt hole of drive plate and torque converter then 
tighten bolts through torque converter housing lower 
plate opening.
Lock drive plate (1) by engaging flat head rod or the 
like (2) with drive plate gear.

Tightening torque
Drive plate to torque converter bolt (a):  25 N·m (
2.5 kg-m, 18.0 lb-ft)

4) Tighten transaxle stiffener bolts to specified torque.
5) Install transaxle housing lower plates (1).

Tightening torque
Transaxle stiffener bolt (a):  55 N·m (5.5 kg-m, 40 
lb-ft)

6) Install starter motor.

Tightening torque
Starter motor bolt and nut:  50 N·m (5.0 kg-m, 
36.5 lb-ft)

7) Remount engine with transaxle assembly to vehicle.

Refer to “Engine Assembly Removal and Installation:  
in Section 1D” for its procedure.

3. Wrench

4. Engine oil pan

I3RM0B510051-

1

(a)

I4RS0A510056-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Бренд: Ultra-tow Страницы: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Бренд: Mercedes-Benz Страницы: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Бренд: Menabo Страницы: 8
Camtree G-51 Instruction Manual preview
G-51
Бренд: Camtree Страницы: 5
Cadillac 2009 CTS Personalization Manual preview
2009 CTS
Бренд: Cadillac Страницы: 20
Baja Designs 447575 Instructions preview
447575
Бренд: Baja Designs Страницы: 5
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
Toyota CAMRY HV Manual preview
CAMRY HV
Бренд: Toyota Страницы: 636
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Бренд: Edelbrock Страницы: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Бренд: GMC Страницы: 439
Classic Accessories OVER DRIVE PolyPRO 3 Car Cover Instructions preview
OVER DRIVE PolyPRO 3 Car Cover
Бренд: Classic Accessories Страницы: 2
VP Autoparts 419420 Installation preview
419420
Бренд: VP Autoparts Страницы: 2
Audiovox Electronics HR7012M Installation Manual preview
HR7012M
Бренд: Audiovox Electronics Страницы: 12
Prime Design VRI3-FT31B Assembly Manual preview
VRI3-FT31B
Бренд: Prime Design Страницы: 16
BMW X1 2015 Owner'S Manual preview
X1 2015
Бренд: BMW Страницы: 242
Monster iCarPlay Direct Connect 2000 User Manual & Warranty Information preview
iCarPlay Direct Connect 2000
Бренд: Monster Страницы: 66

Бренды по названию

Популярные бренды

Загрузить еще бренды