manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1F-9 Engine Cooling System: 

Radiator Cooling Fan Relay Inspection

S4RS0A1606020

1) Disconnect negative (–) cable at battery.
2) Remove radiator cooling fan relay No.1 (1), No.2 (2) 

and/or No.3 (3) from relay box.

3) Check that there is no continuity between terminal 

“C” and “B”. If there is continuity, replace relay.

4) Connect battery positive (+) terminal to terminal “B” 

of relay.

5) Connect battery negative (–) terminal “A” of relay.
6) Check continuity between terminal “C” and “D”. If 

there is no continuity when relay is connected to the 
battery, replace relay.

Radiator Cooling Fan Removal and Installation

S4RS0A1606021

Removal

1) Disconnect negative (–) cable at battery.
2) Disconnect connector (1) of cooling fan motor.

3) Drain coolant.
4) Remove front bumper, front bumper upper absorber 

and upper member referring to “Front Bumper and 
Rear Bumper Components:  in Section 9K”.

5) Remove radiator inlet hose and reservoir hose.
6) Remove cooling fan mounting bolts (1).

7) Slide condenser with radiator, and then remove 

radiator cooling fan.

CAUTION:

Be sure not to damage condenser outlet pipe.

 

Installation

Reverse removal procedure for installation noting the 
following.
• Refill cooling system referring to Step 7) to 22) of 

“Cooling System Flush and Refill: ”.

• After installation, verify there is no coolant leakage at 

each connection.

Radiator On-Vehicle Inspection and Cleaning

S4RS0A1606013

Inspection

Check radiator for leakage or damage. Straighten bent 
fins, if any.

Cleaning

Clean frontal area of radiator cores.

“D”

“B”

“A”

“C”

3

2

1

I4RS0A160007-

1

I4RS0A160008-

I4RS0A160009-

I2RH01160014-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
Lancia Delta Owner'S Handbook Manual preview
Delta
Бренд: Lancia Страницы: 276
T-Tech TT100 User Manual preview
TT100
Бренд: T-Tech Страницы: 38
Vaisala MD30 Setup Manual preview
MD30
Бренд: Vaisala Страницы: 24
Triumph MAYFLOWER 1951 Instruction Book preview
MAYFLOWER 1951
Бренд: Triumph Страницы: 86
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Бренд: Mazda Страницы: 12
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Бренд: Honda Страницы: 85
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Бренд: BrandMotion Страницы: 2
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Бренд: Cadillac Страницы: 34
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Бренд: Easee Страницы: 12
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Daesung HM-TX-315 User Manual preview
HM-TX-315
Бренд: Daesung Страницы: 9
Pontiac 2010 Vibe Owner'S Manual preview
2010 Vibe
Бренд: Pontiac Страницы: 318
RAM Ram 3500 2012 Specifications preview
Ram 3500 2012
Бренд: RAM Страницы: 13
Belkin F8V9017 User Manual preview
F8V9017
Бренд: Belkin Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды