Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 1257

background image

Engine General Information and Diagnosis: 1A-47

DTC Troubleshooting

NOTE:

• Before performed trouble shooting, be sure to read the “Precautions of ECM Circuit Inspection: ”.
• When measuring circuit voltage, resistance and/or pulse signal at ECM connector, connect the

special tool to ECM and/or the ECM connectors referring to “Inspection of ECM and Its Circuits: ”.

• Upon completion of inspection and repair work, perform “DTC Confirmation Procedure” and

confirm that the trouble has been corrected.

Step

Action

Yes

No

1

Was “Engine and Emission Control System Check”
performed?

Go to Step 2.

Go to “Engine and
Emission Control
System Check: ”.

2

HO2S-1 heater power circuit check

1) Disconnect connector from HO2S-1 with ignition switch

turned OFF.

2) Check for proper connection to HO2S-1 at “BLK/WHT”

and “BLK/RED” wire terminals.

3) If wire and connection are OK, measure voltage

between “BLK/WHT” wire terminal and engine ground
with ignition switch turned ON.

Is voltage over 10 V?

Go to Step 3.

“BLK/WHT” wire is open
circuit or shorted to
ground circuit.

3

HO2S-1 heater power circuit check

1) Disconnect connectors from ECM with ignition switch

turned OFF.

2) Measure resistance between “BLK/WHT” wire terminal

of HO2S-1 connector and “E23-29” terminal of ECM
connector.

Is resistance below 5

:

?

Go to Step 4.

“BLK/WHT” wire is high
resistance circuit.

4

HO2S-1 heater drive circuit check

1) Measure resistance between “C37-46” terminal of ECM

connector and vehicle body ground.

Is resistance infinity?

Go to Step 5.

“BLK/RED” wire is
shorted to ground
circuit.

5

HO2S-1 heater drive circuit check

1) Turn ON ignition switch.
2) Measure voltage between “C37-46” terminal of ECM

connector and vehicle body ground.

Is voltage 0 V?

Go to Step 6.

“BLK/RED” wire is
shorted to power circuit.

6

HO2S-1 heater drive circuit check

1) Connect connector to HO2S-1 with ignition switch turned

OFF.

2) Turn ON ignition switch.
3) Measure voltage between “C37-46” terminal of ECM

connector and vehicle body ground with connector
disconnected from ECM.

Is voltage over 10 V?

Go to Step 7.

“BLK/RED” wire is open
circuit.

«
...
93
94
95
96
97
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

witty park XEV6 Series

Бренд: hager Страницы: 9

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: EEZ RV Страницы: 31

Parrot MKi + ParrotCK3100 range LOGAN

Бренд: Parrot Страницы: 10

inView 360 Fusion

Бренд: Safe Fleet Страницы: 27

ROADSIDE ASSISTANCE

Бренд: Seat Страницы: 44

Бренд: RAM Страницы: 496

Akerstroms Tx700

Бренд: LXE Страницы: 146

Бренд: Honda Страницы: 124

Бренд: Lantronix Страницы: 51

Бренд: Prorack Страницы: 15

Бренд: Navman Страницы: 10

Бренд: Macrom Страницы: 10

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Бренд: ADS Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды