manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9D-9 Wipers / Washers: 

Rear Wiper and Washer Switch Inspection

S4RS0A9406009

Check for continuity between terminals at each switch 
position. If check result is not as specified, replace 
switch.

Rear Wiper Relay Removal and Installation

S4RS0A9406015

Removal

1) Disconnect negative (–) cable at battery.
2) Remove junction block assembly referring to “BCM 

(Included in Junction Block Assembly) Removal and 
Installation:  in Section 10B”.

3) Remove rear wiper relay.

Installation

Reverse removal procedure for installation.

Rear Wiper Relay Inspection

S4RS0A9406014

1) Check that there is no continuity between terminal 

“3” and “4”. If there is continuity, replace relay.

2) Connect battery positive (+) terminal to terminal “2” 

of relay.

3) Connect battery negative (–) terminal to terminal “1” 

of relay.

4) Check continuity between terminal “3” and “4”. If 

there is no continuity when relay is connected to the 
battery, replace relay.

Specifications

Tightening Torque Specifications

S4RS0A9407001

NOTE:
The specified tightening torque is also described in the following.
“Wipers and Washers Components: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

Terminal

Position

OFF

INTO

1

2

4

3

WASH

ON

ON + WASH

ON + WASH

INT

ON

WASH

1

2

3

4

I4RS0A940027-

“4”

“2”

“1”

“3”

I4RS0A940028-

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Washer tank bolt

4

0.4

3.0

)

Windshield wiper bolt

8

0.8

6.0

)

Windshield wiper arm nut

16

1.6

11.5

)

Rear wiper motor mounting bolt

8

0.8

6.0

)

Rear wiper nut

5

0.5

4.0

)

Rear wiper arm nut

8

0.8

6.0

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Бренд: Q'STRAINT Страницы: 10
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Бренд: Uniden Страницы: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Бренд: Uniden Страницы: 20
Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
Fiat 500 L 2019 User Manual preview
500 L 2019
Бренд: Fiat Страницы: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Бренд: Honda Страницы: 6
Draw tite 24943 Installation Instructions preview
24943
Бренд: Draw tite Страницы: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Бренд: Mercedes-Benz Страницы: 329
Daesung HM-TX-315 User Manual preview
HM-TX-315
Бренд: Daesung Страницы: 9
Pontiac 2010 Vibe Owner'S Manual preview
2010 Vibe
Бренд: Pontiac Страницы: 318
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
Streetwize SWGH3 Quick Start Manual preview
SWGH3
Бренд: Streetwize Страницы: 4
Prorack K663 Fitting Instructions Manual preview
K663
Бренд: Prorack Страницы: 15
Mazda 2008 B2300 Truck Owner'S Manual preview
2008 B2300 Truck
Бренд: Mazda Страницы: 280
Z Flash OBD-II STALK User Manual preview
OBD-II STALK
Бренд: Z Flash Страницы: 4
Whispbar K684W Fitting Instructions Manual preview
K684W
Бренд: Whispbar Страницы: 15
Master Tailgaters MR-43E2DVR1 User Manual preview
MR-43E2DVR1
Бренд: Master Tailgaters Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды