Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 705

Страница: 705 / 1257

Automatic Transmission: 5A-165

91) Bend dents of lock washer (1) in order to prevent

displacement of lock washer.

92) Install manual select lever (1).

Tightening torque
Manual select lever nut (a): 13 N·m (1.3 kg-m,
9.5 lb-ft)

93) Install engine mounting LH bracket (1).

Tightening torque
Engine mounting LH bracket bolt (a): 55 N·m (
5.5 kg-m, 40.0 lb-ft)

94) Install torque converter (3) noting the following

points.

CAUTION:

• Before installing converter, make sure that

its pump hub portion is free from nicks,
burrs or damage which may cause oil seal
to leak.

• Be very careful not to drop converter on oil

pump gear. Damage in gear, should it
occur, may cause a critical trouble.

• Install torque converter aligning grooves (1) of

torque converter and projection (2) of oil pump
drive gear.

• Install torque converter, using care not to damage

oil seal of oil pump.

• After installing torque converter, check that

distance “a” is within specification.

Torque converter installing position
“a”: More than 19.9 mm (0.783 in.)

• Check torque converter for smooth rotation.
• Apply grease around cup (6) at the center of

torque converter.

“C”: Grease 99000–25010

I3RM0B510074-

I3RM0B510075-

(a)

I3RM0B510076-

I3RM0B510077-

4. Flange nut
5. Torque converter housing

I2RH0B510337-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды