Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 640

Страница: 640 / 1257

5A-100 Automatic Transmission:

Installation

1) Install shift solenoid valve-A (No.1) (1), shift solenoid

valve-B (No.2) (2) and timing solenoid valve (3).

Tightening torque
Shift solenoid bolt (a): 11 N·m (1.1 kg-m, 8.0 lb-
ft)

2) Connect solenoid connectors identifying their

installing positions by wire color.

3) Install transmission fluid sensor (6) and sensor wire

to clamp.

4) Install oil strainer assembly (1).

Tightening torque
Oil strainer bolt (a): 10 N·m (1.0 kg-m, 7.5 lb-ft)

5) Install new oil pan gasket (1) and oil pan (2).
6) Tighten oil pan bolts to specified torque diagonally

and little by little.

Tightening torque
Oil pan bolt (b): 7.0 N·m (0.7 kg-m, 5.0 lb-ft)

Solenoid Valves (Shift Solenoid Valves, and
Timing Solenoid Valve) Inspection

S4RS0A5106016

Resistance Check

Check shift solenoid valves and timing solenoid valve.

Shift solenoid valves and timing solenoid valve
resistance
Standard: 11 – 15

at 20

C (68

Solenoid coupler

Wire color

Shift solenoid valve-A (No.1) (2)

White

Shift solenoid valve-B (No.2) (3)

Black

Timing solenoid valve (1)

Yellow

TCC pressure control solenoid
valve (4)

Light green / Brown

Pressure control solenoid valve
(5)

Green / Gray

(a)

I4RS0A510029-

I4RS0A510030-

I2RH0B510059-

I2RH0B510060-

I2RH0B510061-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды