manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1G-11 Fuel System: 

Fuel Tank Inlet Valve Removal and Installation

S4RS0A1706015

WARNING:

Before starting the following procedure, be 
sure to observe “Precautions on Fuel System 
Service: ” in order to reduce the risk or fire 
and personal injury.

 

Removal

1) Remove fuel filler cap.
2) Insert hose of a hand operated pump into fuel filler 

hose (1) and drain fuel in space “A” as shown in 
figure.

CAUTION:

Do not force pump hose into fuel tank, or 
pump hose may damage to fuel tank inlet 
valve (2).

 

3) Hoist vehicle, and remove clamp (2) and fuel filler 

hose (1) from fuel tank.

4) Remove fuel tank inlet valve (1) using flat head rod 

(2) or the like.

CAUTION:

Be careful not to damage fuel tank inlet valve 
(1) with flat head rod (2) or the like.

 

Installation

1) Install fuel tank inlet valve (1) to fuel tank.

2) Install fuel filler hose (1) to fuel tank and secure it 

with clamp (2).
For proper installation, refer to “Fuel Hose 
Disconnecting and Reconnecting: ”.

3) Lower vehicle and install fuel filler cap.

IYSQ01170010-

1

2

I4RS0A170007-

I2RH0B170017-

I2RH0B170018-

1

2

I4RS0A170007-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Бренд: Brodit Страницы: 2
XTC ATS-POL-GBU Manual preview
ATS-POL-GBU
Бренд: XTC Страницы: 4
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Бренд: Mercedes-Benz Страницы: 54
Volvo B13R Driver'S Handbook Manual preview
B13R
Бренд: Volvo Страницы: 24
Aries 205039 Installation Manual preview
205039
Бренд: Aries Страницы: 5
Mercedes-Benz MY17 c-class Operator'S Manual preview
MY17 c-class
Бренд: Mercedes-Benz Страницы: 354
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Бренд: DEFA Страницы: 28
Steelmate PTS800V7 User Manual preview
PTS800V7
Бренд: Steelmate Страницы: 14
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Бренд: Lexus Страницы: 830
Mopar 82214480 Manual preview
82214480
Бренд: Mopar Страницы: 17
Toyota 2012 Sienna Owner'S Manual preview
2012 Sienna
Бренд: Toyota Страницы: 779
Kia Optima 2004 Owner'S Manual preview
Optima 2004
Бренд: Kia Страницы: 233
Mercedes-Benz ML 320 CDI Operator'S Manual preview
ML 320 CDI
Бренд: Mercedes-Benz Страницы: 585
JBA 1528S Installation Instructions And Warranty Information preview
1528S
Бренд: JBA Страницы: 5
APS iBoard IB-R159 Manual preview
iBoard IB-R159
Бренд: APS Страницы: 4
Cadillac 2011 Cadillac Owner Assistance Information preview
2011 Cadillac
Бренд: Cadillac Страницы: 48
SAAS MUSCLE Series Quick Start Manual preview
MUSCLE Series
Бренд: SAAS Страницы: 3
Nuna Pipa TW 2 Manual preview
Pipa TW 2
Бренд: Nuna Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды