manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Front Suspension:  2B-5

NOTE:
When servicing component parts of strut 
assembly, remove strut rod cap and then 
loosen strut nut a little before removing strut 
assembly. This will make service work easier. 
Note, however, nut must not be removed at 
this point.

 

2) Hoist vehicle, allowing front suspension to hang free.
3) Remove wheel and disconnect stabilizer joint (1) 

from strut bracket.
When loosening joint nut, hold stud with special 
tools.

Special tool
(A):  09900–00411 (socket)
(B):  09900–00413 (5 mm)

4) Remove brake hose mounting bolt (1) and take off 

brake hose (2) and then ABS wheel speed sensor 
harness (3) (if equipped) from strut bracket as shown 
in figure.

5) Remove strut bracket bolts and nuts (4).

6) Remove strut rod cap.
7) Remove strut nut (1), and remove rebound stopper 

(2).

NOTE:
Hold strut by hand so that it will not fall off.

 

8) Remove strut assembly.

Installation

Install strut assembly by reversing removal procedure, 
noting the following instructions.
• Insert bolts in such direction as shown in figure.
• Tighten all fasteners to specified torque.

Tightening torque
Strut bracket nut (a):  105 N·m (10.5 kg-m, 76.0 lb-
ft)
Brake hose mounting bolt (c):  25 N·m (2.5 kg-m, 
18.0 lb-ft)
Stabilizer joint nut (d):  50 N·m (5.0 kg-m, 36.5 lb-
ft)

• Lower hoist and vehicle in non-loaded condition, 

tighten strut nut (b) to specified torque.

Tightening torque
Strut nut (b):  50 N·m (5.0 kg-m, 36.5 lb-ft)

CAUTION:

• Don twist brake hose and ABS wheel 

speed sensor harness (if equipped) when 
installing it.

• Install ABS wheel speed sensor harness (if 

equipped) to strut bracket as shown in 
figure.

 

1

(A)

(B)

I4RS0A220004-

1

3

2

2

1

4

4

3

I4RS0A220005-

2

1

I4RS0A220006-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

VanEssa mobilcamping V1 User Instruction preview
V1
Бренд: VanEssa mobilcamping Страницы: 8
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Бренд: Eaton Страницы: 12
Parrot CK3300 Setup Information Manual preview
CK3300
Бренд: Parrot Страницы: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Бренд: Parrot Страницы: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Бренд: Parrot Страницы: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Бренд: Parrot Страницы: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Бренд: Parrot Страницы: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Бренд: Parrot Страницы: 106
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Бренд: Zavoli Страницы: 26
Cadillac ESCALADE FAMILY - SPECIFICATIONS 2011 Specifications preview
ESCALADE FAMILY - SPECIFICATIONS 2011
Бренд: Cadillac Страницы: 1
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Gator GX5HDKT User Manual preview
GX5HDKT
Бренд: Gator Страницы: 8
Globalsat MR-350P Installation Manual preview
MR-350P
Бренд: Globalsat Страницы: 2
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Бренд: TATA Motors Страницы: 136
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Бренд: Jaeger Страницы: 11
Cadillac XLR-V Specifications preview
XLR-V
Бренд: Cadillac Страницы: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Бренд: Buick Страницы: 20
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Бренд: Lexus Страницы: 830

Бренды по названию

Популярные бренды

Загрузить еще бренды