Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 575

Страница: 575 / 1257

Automatic Transmission: 5A-35

Poor 3

4 shift

Shift solenoid valve-B circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Pressure control solenoid valve circuit
faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Timing solenoid valve circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Output shaft speed sensor (VSS) circuit
faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Input shaft speed sensor circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Transmission range sensor circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Transmission fluid temperature sensor
circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

CAN communication circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Throttle position sensor circuit faulty

Inspect circuit for open, short and intermittent
referring to “DTC P0122: Throttle Position
Sensor Circuit Low: in Section 1A” and/or
“DTC P0123: Throttle Position Sensor Circuit
High: in Section 1A”. If NG, repair.

Engine coolant temperature sensor
circuit faulty

Inspect circuit for open, short and intermittent
referring to “DTC P0117: Engine Coolant
Temperature Circuit Low: in Section 1A” and/
or “DTC P0118: Engine Coolant Temperature
Circuit High: in Section 1A”. If NG, repair.

Crankshaft position sensor circuit faulty

Inspect circuit for open, short and intermittent
referring to “DTC P0335: Crankshaft Position
(CKP) Sensor Circuit: in Section 1A”. If NG,
repair.

“3” position switch circuit faulty

Refer to “No Gear Shift to 4th gear: ”.

TCM

Substitute a known-good TCM and recheck.

ECM

Substitute a known-good ECM and recheck.

Poor 4

3 shift

Shift solenoid valve-B circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Pressure control solenoid valve circuit
faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Timing solenoid valve circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Output shaft speed sensor (VSS) circuit
faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Input shaft speed sensor circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

CAN communication circuit faulty

Inspect circuit for open, short and intermittent.
If NG, repair.

Throttle position sensor circuit faulty

“3” position switch circuit faulty

Refer to “No Gear Shift to 4th gear: ”.

TCM

Substitute a known-good TCM and recheck.

ECM

Substitute a known-good ECM and recheck.

Condition

Possible cause

Correction / Reference Item

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды