manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-114 Automatic Transmission: 

15) Remove valve body harness (1).

CAUTION:

When pulling valve body harness out of 
transaxle case, take care not to damage 
transmission fluid temperature sensor (2) at 
narrow exit of case.
Careless sensor treatment might cause 
sensor malfunction.

 

16) Remove governor apply No.1 gasket (1).

17) Remove cooler check valve (1) and spring (2).

18) Remove accumulator pistons and springs.

To remove C2 (1), C1 (2) and B1 (3) accumulator 
pistons and springs, position rag on pistons to catch 
each piston. To remove pistons, force low-pressure 
compressed air (1 kg/cm

2

, 15 psi, 100 kPa, max) into 

hole (4) as shown in figure, and pop each piston into 
rag.

NOTE:
Do not push accumulator pistons with 
fingers or anything before removing them. 
Pushing them may cause compressed fluid 
in accumulator to spew out of hole and get to 
your face and clothes.

 

I2RH0B510091-

I2RH0B510092-

I2RH0B510093-

I2RH0B510094-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Бренд: Jacob Jensen Страницы: 28
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Бренд: Chrysler Страницы: 1534
Raptor Series MAGNUM RT Series Manual preview
MAGNUM RT Series
Бренд: Raptor Series Страницы: 6
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Бренд: TATA Motors Страницы: 236
Brodit ProClip 854208 Manual preview
ProClip 854208
Бренд: Brodit Страницы: 2
Westin 31-0190 Installation Instructions preview
31-0190
Бренд: Westin Страницы: 2
Sagem MyCK100 User Manual preview
MyCK100
Бренд: Sagem Страницы: 10
Fabbri BICI OK 2 Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 32
Whelen Engineering Company SAK34 Installation Manual preview
SAK34
Бренд: Whelen Engineering Company Страницы: 2
Mazda MX-3 1995 Workshop Manual preview
MX-3 1995
Бренд: Mazda Страницы: 1001
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Бренд: Acura Страницы: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Бренд: Ford Страницы: 325
Connects2 PARK-401 User Manual preview
PARK-401
Бренд: Connects2 Страницы: 2
wtw spectroFlex Car Adapter Operating Manual preview
spectroFlex Car Adapter
Бренд: wtw Страницы: 4
CITROEN 2 CV4 Owner'S Manual preview
2 CV4
Бренд: CITROEN Страницы: 86
Waeco MagicWatch MWE850 Installation And Operating Manual preview
MagicWatch MWE850
Бренд: Waeco Страницы: 200

Бренды по названию

Популярные бренды

Загрузить еще бренды