manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-129

Specifications

Tightening Torque Specifications

S4RS0A8207001

NOTE:
The specified tightening torque is also described in the following.
“Air Bag System Components, Wiring and Connectors Location: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

Special Tools and Equipment

Use of Special Tools

S4RS0A8208003

WARNING:

To avoid deployment when troubleshooting 
the air bag system, do not use electrical test 
equipment such as a battery powered or AC 
powered voltmeter, ohmmeter, etc., or any 
type of electrical equipment other than that 
specified. Do not use a non-powered probe 
type tester.
Instructions must be followed carefully, 
otherwise personal injury may result.

 

You should be familiar with the tools listed under the 
heading “Special Tool”. You should be able to measure 
voltage and resistance. You should be familiar with 
proper use of a scan tool such as Air Bag Driver / 
Passenger Load Tool, Connector Test Adapter Kit and 
the Digital Multimeter.

Special tool
(A):  09932-76010 (Connector Test Adapter Kit)

This must be used whenever a diagnostic procedure 
requests checking or probing a terminal.
Using the appropriate adapter in the special tool will 
ensure that no damage to the terminal will occur from the 
multimeter probe, such as spreading or bending.

The adapter (1) will also give an idea of whether or not 
contact tension is sufficient, helping to find an open or 
intermittent open due to poor terminal contact. An SDM 
short bar release tool (2) is included in the connector test 
adapter kit. Inserting it into the SDM connector (3) will 
releases the shorting bar.

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

SDM bolt

9

0.9

6.5

)

Driver air bag (inflator) module mounting bolt

9

0.9

6.5

)

Passenger air bag (inflator) module attaching 
bolt

23

2.3

16.5

)

Sleeve lock nut

2.5

0.25

2.0

)

Side curtain-air bag (inflator) module attaching 
bolts

11

1.1

8.0

)

Forward-sensor mounting bolt

9

0.9

6.5

)

Side-sensor bolt

9

0.9

6.5

)

I3JA01820041-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Бренд: Metra Electronics Страницы: 14
Parrot CK3300 Setup Information Manual preview
CK3300
Бренд: Parrot Страницы: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Бренд: Parrot Страницы: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Бренд: Parrot Страницы: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Бренд: Parrot Страницы: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Бренд: Parrot Страницы: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Бренд: Parrot Страницы: 106
Kuda-Phonebase 055040 Installation Instruction preview
055040
Бренд: Kuda-Phonebase Страницы: 3
Jacobsen Cushman Turf Truckster Parts & Maintenance Manual preview
Cushman Turf Truckster
Бренд: Jacobsen Страницы: 210
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Бренд: Mitsubishi Страницы: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Бренд: Cadillac Страницы: 442
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Kargo Master 8006A Instruction Manual preview
8006A
Бренд: Kargo Master Страницы: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Бренд: Safe Fleet Страницы: 12
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
RBO IT FITS RBO1018 Product Manual preview
IT FITS RBO1018
Бренд: RBO Страницы: 36
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Бренд: KLAUS Multiparking Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды