manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

ABS:  4E-32

Front Wheel Speed Sensor Ring Removal and 
Installation

S4RS0A4506012

NOTE:
The front wheel sensor ring can not be 
removed or replaced alone. If front wheel 
sensor ring needs to be replaced, replace it 
as a wheel side joint assembly of drive shaft.

 

For removal and installation of wheel side joint assembly 
of drive shaft, referring to “Front Drive Shaft 
Disassembly and Assembly:  in Section 3A”.

Rear Wheel Speed Sensor Ring On-Vehicle 
Inspection

S4RS0A4506013

• Check ring serration (teeth) (1) for being missing, 

damaged or deformed.

• Turn wheel and check if ring rotation is free from 

eccentricity and looseness.

• Check that no foreign material is attached.

If any faulty is found, repair or replace.

Rear Wheel Speed Sensor Ring Removal and 
Installation

S4RS0A4506014

For removal and installation of rear wheel speed sensor 
ring, refer to “ABS Sensor Ring Removal and Installation 
(If Equipped):  in Section 4C”.

Specifications

Tightening Torque Specifications

S4RS0A4507001

NOTE:
The specified tightening torque is also described in the following.
“Front Wheel Speed Sensor Components Location: ”
“Rear Wheel Speed Sensor Components Location: ”
“ABS Hydraulic Unit / Control Module Assembly Components: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

1

I4RS0A450033-

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Brake pipe flare nut

16

1.6

11.5

)

ABS hydraulic unit / control module assembly 
bolt

9

0.9

6.5

)

ABS hydraulic unit / control module assembly 
bracket bolt

25

2.5

18.0

)

Front wheel speed sensor bolt

25

2.5

18.0

)

Front wheel speed sensor harness clamp bolt 

11

1.1

8.0

)

Rear wheel speed sensor bolt

11

1.1

8.0

)

Rear wheel speed sensor harness clamp bolt

11

1.1

8.0

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Valeo SC400 Operating Instructions Manual preview
SC400
Бренд: Valeo Страницы: 17
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Rati Armster 2 User Manual preview
Armster 2
Бренд: Rati Страницы: 2
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Бренд: Cadillac Страницы: 34
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Бренд: Honda Страницы: 390
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Volvo S90 - ACCESSORY PANEL Owner'S Manual Supplement preview
S90 - ACCESSORY PANEL
Бренд: Volvo Страницы: 166
FIRRAK FIRRAK arca Assembly Instructions Manual preview
FIRRAK arca
Бренд: FIRRAK Страницы: 12
Mazda Auto-Dimming Mirror User Manual preview
Auto-Dimming Mirror
Бренд: Mazda Страницы: 2
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Бренд: Kleinn Air Horns Страницы: 33
Wallbox PLP1 Installation Manual preview
PLP1
Бренд: Wallbox Страницы: 21
Curt Group Aries 2074113 Installation Manual preview
Aries 2074113
Бренд: Curt Group Страницы: 2
Datsun Saloon I300 Workshop Manual preview
Saloon I300
Бренд: Datsun Страницы: 104
Harbor Freight Tools 95058 Installation And Operation Instructions Manual preview
95058
Бренд: Harbor Freight Tools Страницы: 8
Ford 2003 Ranger Quick Reference Manual preview
2003 Ranger
Бренд: Ford Страницы: 2
Toyota 4Runner 2020 Owner'S Manual preview
4Runner 2020
Бренд: Toyota Страницы: 596
Audiovox CDC-TO3 Installation Manual preview
CDC-TO3
Бренд: Audiovox Страницы: 2
Fortin EVO ONE THAR-GM7 Installation Instructions Manual preview
EVO ONE THAR-GM7
Бренд: Fortin Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды