manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1B-1 Aux. Emission Control Devices: 

Aux. Emission Control Devices

 

Diagnostic Information and Procedures

EGR System Inspection

S4RS0A1204001

1) Connect SUZUKI scan tool to data link connector 

(DLC) with ignition switch turned OFF.

2) Turn ON ignition switch and erase DTC using 

“CLEAR DTC” in “TROUBLE CODES” menu.

3) Start engine and warm it up to normal operating 

temperature then select “DATA LIST” mode on scan 
tool.

4) Make sure that vehicle condition is as follows.

• Vehicle speed = 0 km/h (0 KPH)
• Engine speed 

d

 900 rpm

• Engine coolant temp. 

t

 90 

q

C, 164 

q

F

5) With engine idling (without depressing accelerator 

pedal), open EGR valve by using “STEP EGR” mode 
in “MISC TEST” menu. In this state, as EGR valve 
opening increases engine idle speed drops. If not, 
possible cause is clogged EGR gas passage, stuck 
or faulty EGR valve.

Repair Instructions

EVAP Canister Purge Inspection

S4RS0A1206001

NOTE:
Before inspection, check to make sure that 
gear shift lever is in neutral position (with A/T 
model, selector lever in “P” range) and that 
parking brake lever is pulled all the way up.

 

1) Disconnect purge hose (1) from EVAP canister (2).
2) Place finger against the end of disconnected hose 

and check that vacuum is not felt there when engine 
is cool and running at idle speed. If check result is 
not satisfactory, check EVAP canister purge valve, 
wire harness and ECM.

EVAP Canister Purge Valve and Its Circuit 
Inspection

S4RS0A1206002

WARNING:

Do not apply vacuum by mouth; otherwise 
harmful fuel vapor can be breathed in.

 

CAUTION:

Do not apply vacuum more than –86 kPa (–
12.47 psi); otherwise EVAP canister purge 
valve could be damaged.

 

1) Prepare to operate EVAP canister purge valve as 

follows.
a) When using SUZUKI scan tool:

i)

Connect SUZUKI scan tool to DLC (1) with 
ignition switch turned OFF and disconnect 
purge valve vacuum hoses from intake 
manifold and EVAP canister.

1. SUZUKI scan tool display
2. EGR valve opening (0: Close, 100: Full open)

Step EGR

Step EGR Flow Duty                          21 %
Step EGR   (con)                                23% 
Engine Speed                                   771 RPM
Desired Idle                                      698 RPM
IAC Flow Duty                                 20.0 %     
Ignition Advance                              11.5  BTDC 
Closed Throttle Pos                             ON

1

2

I4RS0A120001-

1

2

I4RS0A120002-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Acdeos AXS FL Manual preview
AXS FL
Бренд: Acdeos Страницы: 38
Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Бренд: Jacob Jensen Страницы: 28
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Бренд: GReddy Страницы: 9
Fiat 500 L 2019 User Manual preview
500 L 2019
Бренд: Fiat Страницы: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Бренд: Honda Страницы: 6
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Бренд: CITROËN Страницы: 301
NavLinkz RL2-SC14 Manual preview
RL2-SC14
Бренд: NavLinkz Страницы: 21
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Бренд: Easee Страницы: 12
iOttie Aivo Connect Setup Manual preview
Aivo Connect
Бренд: iOttie Страницы: 58
Toyota CAMRY HV Manual preview
CAMRY HV
Бренд: Toyota Страницы: 636
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Бренд: E&G Classics Страницы: 4
Mitsubishi Montero 1988 Manual preview
Montero 1988
Бренд: Mitsubishi Страницы: 367
Subaru 2015 Forester Quick Reference Manual preview
2015 Forester
Бренд: Subaru Страницы: 16
Husky 31564 Assembly, Installation, Operation And Maintenance Instructions preview
31564
Бренд: Husky Страницы: 8
Dodge 2004 JR41 Stratus Sedan Owner'S Manual preview
2004 JR41 Stratus Sedan
Бренд: Dodge Страницы: 273
Westin 33-1920 Instructions preview
33-1920
Бренд: Westin Страницы: 3
Buick 2014 LaCrosse Manual preview
2014 LaCrosse
Бренд: Buick Страницы: 112
Porsche 1972 911 Workshop Manual preview
1972 911
Бренд: Porsche Страницы: 1005

Бренды по названию

Популярные бренды

Загрузить еще бренды