manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5B-7 Manual Transmission: 

Vehicle Speed Sensor (VSS) Removal and 
Installation

S4RS0A5206027

Removal

1) Remove battery and tray with coolant reservoir.
2) Disconnect gear shift and select control cables (1) 

from transaxle.

3) Remove cable bracket (1) from transaxle.
4) Disconnect VSS coupler (2).
5) Remove VSS.

Installation

1) Apply oil to new O-ring (1) and then install VSS to 

transaxle.

Tightening torque
VSS bolt (a):  5 N·m (0.5 kg-m, 4.0 lb-ft)

2) Connect VSS coupler (1).
3) Install cable bracket (2) to transaxle.

Tightening torque
Cable bracket bolt (a):  55 N·m (5.5 kg-m, 40.0 lb-
ft)

4) Connect gear shift and select control cables (1) to 

transaxle.

5) Install battery and tray, and then install coolant 

reservoir to battery tray.

Back Up Lamp Switch Removal and Installation

S4RS0A5206007

Removal

1) Remove battery and tray with coolant reservoir.
2) Disconnect back up lamp switch coupler (1).
3) Remove back up lamp switch (2).

1

I4RS0A520006-

1

2

I4RS0A520007-

I4RS0A520008-

3. Gear shift and select shaft assembly

2

(a)

1

I4RS0A520009-

1

I4RS0A520006-

3

1

2

I4RS0A520010-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Calira 811 Manual preview
811
Бренд: Calira Страницы: 14
Wagan 2591 User Manual preview
2591
Бренд: Wagan Страницы: 12
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Бренд: Safe Fleet Страницы: 38
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Бренд: Enduro Страницы: 48
HAUL MASTER 41782 Assembly And Operating Instructions Manual preview
41782
Бренд: HAUL MASTER Страницы: 8
BMW M5 2014 Service And Warranty Information preview
M5 2014
Бренд: BMW Страницы: 38
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Бренд: TATA Motors Страницы: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Бренд: Safe Fleet Страницы: 12
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Бренд: Cadillac Страницы: 352
Oldsmobile Bravada 1997 Owner'S Manual preview
Bravada 1997
Бренд: Oldsmobile Страницы: 358
Mitsubishi Montero 1988 Manual preview
Montero 1988
Бренд: Mitsubishi Страницы: 367
Whispbar K684W Fitting Instructions Manual preview
K684W
Бренд: Whispbar Страницы: 15
Maserati MC 20 2022 Roadside Assistance Manual preview
MC 20 2022
Бренд: Maserati Страницы: 37
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Бренд: Blue Ox Страницы: 9
Buick Riviera 1967 Owner'S Manual preview
Riviera 1967
Бренд: Buick Страницы: 58
Mazda Auto-Dimming Mirror User Manual preview
Auto-Dimming Mirror
Бренд: Mazda Страницы: 2
BENDIX C-5 CUT OUT COCK Manual preview
C-5 CUT OUT COCK
Бренд: BENDIX Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды