manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

3A-9 Drive Shaft / Axle: 

4) Install right oil seal (1) to center bearing support (2) 

until it become flush with bearing support using 
special tool, and then apply grease to oil seal lip.

“A”:  Grease 99000–25010

Special tool
(A):  09913–85210

Front Drive Shaft Inspection

S4RS0A3106005

• Check shaft and joint for damage, wear or bend. 

Replace them as necessary.

• Check retaining ring and snap ring for breakage or 

deformation. Replace as necessary.

• Check boots for breakage or deterioration.

Specifications

Tightening Torque Specifications

S4RS0A3107001

NOTE:
The specified tightening torque is also described in the following.
“Front Drive Shaft Assembly Components Location: ”
“Front Drive Shaft Components: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

I4RS0A310019-

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Brake hose mounting bolt

25

2.5

18.0

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Бренд: Waeco Страницы: 212
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Бренд: iDataLink Страницы: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Бренд: Magneti Marelli Страницы: 2
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Бренд: CITROËN Страницы: 301
muth signal mirror Instalation Instructions preview
signal mirror
Бренд: muth Страницы: 10
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Бренд: Connects2 Страницы: 4
Ranger design 1525-NS Installation Manual preview
1525-NS
Бренд: Ranger design Страницы: 22
National Cycle Quantum hardcoated N30216 Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30216
Бренд: National Cycle Страницы: 3
Beper P205DIF100 Manual preview
P205DIF100
Бренд: Beper Страницы: 52
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Бренд: Discount Car Stereo Страницы: 8
Webasto Telestart T70 Installation Instructions Manual preview
Telestart T70
Бренд: Webasto Страницы: 23
Waeco MagicSpeed MS900 Installation Manual preview
MagicSpeed MS900
Бренд: Waeco Страницы: 120
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Бренд: Waeco Страницы: 3
Or-Fab HD Bumper Installation Instructions preview
HD Bumper
Бренд: Or-Fab Страницы: 4
CITROËN Jumpy Miltispace Owner'S Handbook Manual preview
Jumpy Miltispace
Бренд: CITROËN Страницы: 164
Directed MIT4 Firmware Specific Manual preview
MIT4
Бренд: Directed Страницы: 30
Chevrolet Chevy II 1965 Owner'S Manual preview
Chevy II 1965
Бренд: Chevrolet Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды