manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine General Information and Diagnosis:  1A-147

Troubleshooting

NOTE:

• Before performed trouble shooting, be sure to read the “Precautions of ECM Circuit Inspection: ”.
• When measuring circuit voltage, resistance and/or pulse signal at ECM connector, connect the 

special tool to ECM and/or the ECM connectors referring to “Inspection of ECM and Its Circuits: ”.

• Upon completion of inspection and repair work, perform “DTC Confirmation Procedure” and 

confirm that the trouble has been corrected.

 

Step

Action

Yes

No

1

Was “Engine and Emission Control System Check” 
performed?

Go to Step 2.

Go to “Engine and 
Emission Control 
System Check: ”.

2

DTC check

1) Connect scan tool to DLC with ignition switch turned 

OFF.

2) Check ECM, TCM (equipped with A/T) and BCM for 

DTC.

Is there any DTC(s) (other than DTC P1674, P1675, P1676, 
P1678 in ECM, DTC P1774, P1775, P1777, P1778 in TCM 
(equipped with A/T) and DTC U1073, U1001, U1100, U1101 
in BCM)?

Go to applicable DTC 
diag. flow.

Go to Step 3.

3

ECM, TCM (equipped with A/T), BCM and combination 
meter connectors check

1) Check for proper connection at each ECM, TCM 

(equipped with A/T), BCM and combination meter 
connector terminals with ignition switch turned OFF.

2) If connections are OK, recheck ECM for DTC with 

engine running.

Is there DTC P1674?

Go to Step 4.

Intermittent trouble. 
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”

4

ECM power and ground circuit check

1) Check ECM power and ground circuit referring to “ECM 

Power and Ground Circuit Check: ”.

Are they in good condition?

Go to Step 5.

Repair ECM power and/
or ground circuits.

5

DTC check in BCM and TCM (equipped with A/T) (bus 
off)

1) Check DTC(s) in TCM (equipped with A/T) and BCM.

Is there DTC(s) P1774 in TCM (equipped with A/T) and/or 
U1073 in BCM?

Go to Step 6.

Go to Step 7.

6

DTC check in ECM (bus off)

1) Disconnect connectors from ECM with ignition switch 

turned OFF.

2) Check TCM (equipped with A/T) and BCM for DTC(s).

Is there DTC(s) P1774 in TCM (equipped with A/T) and/or 
U1073 in BCM?

Go to Step 7.

Substitute a known-
good ECM and recheck.

7

DTC check in ECM

1) Connect connectors to ECM and disconnect connectors 

from TCM (equipped with A/T) with ignition switch turned 
OFF.

2) Check ECM for DTC.

Is there DTC P1674?

Go to Step 8.

Substitute a known-
good TCM (equipped 
with A/T) and recheck.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Бренд: Metra Electronics Страницы: 14
Jeep Automobile Service And Warranty Handbook preview
Automobile
Бренд: Jeep Страницы: 42
Jeep Automobile Warranty Information Booklet preview
Automobile
Бренд: Jeep Страницы: 44
Cadillac ATS 2015 Convenience/Personalization Manual preview
ATS 2015
Бренд: Cadillac Страницы: 20
Jeep Automobile Service Contract preview
Automobile
Бренд: Jeep Страницы: 7
Cadillac 2016 ELR Convenience/Personalization Manual preview
2016 ELR
Бренд: Cadillac Страницы: 20
Cadillac 2016 CTS Manual preview
2016 CTS
Бренд: Cadillac Страницы: 354
Cadillac 2005 CTS Personalization Manual preview
2005 CTS
Бренд: Cadillac Страницы: 20
Cadillac 2014 XTS Convenience/Personalization Manual preview
2014 XTS
Бренд: Cadillac Страницы: 20
Cadillac ATS 2014 Specifications preview
ATS 2014
Бренд: Cadillac Страницы: 10
Cadillac 2013 Escalade ESV Owner'S Manual preview
2013 Escalade ESV
Бренд: Cadillac Страницы: 524
Cadillac 2013 ATS Personalization Manual preview
2013 ATS
Бренд: Cadillac Страницы: 20
Cadillac ATS 2013 Owenrs Manual preview
ATS 2013
Бренд: Cadillac Страницы: 438
Cadillac 2013 ATS Owner'S Manual preview
2013 ATS
Бренд: Cadillac Страницы: 450
Cadillac 2011 Escalade Hybrid Owner'S Manual Addendum preview
2011 Escalade Hybrid
Бренд: Cadillac Страницы: 94
Cadillac 2011 Escalade Hybrid Owner'S Manual preview
2011 Escalade Hybrid
Бренд: Cadillac Страницы: 94
Cadillac 2011 CTS COUPE Navigation Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 78
Cadillac 2011 CTS COUPE Brochure preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды