manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine Cooling System:  1F-10

Radiator Removal and Installation

S4RS0A1606014

Removal

1) Disconnect negative cable at battery.
2) Drain A/T fluid.
3) Drain coolant.
4) Remove cooling fan assembly referring to “Radiator 

Cooling Fan Removal and Installation: ”.

5) Remove A/T fluid cooler inlet and outlet hoses.
6) Remove radiator outlet hose from radiator.
7) Remove radiator from vehicle.

Installation

Reverse removal procedures, noting the following.
• Refill cooling system referring to Step 7) to 22) of 

“Cooling System Flush and Refill: ”.

• After installation, verify there is no coolant leakage 

each connection.

• Refill A/T fluid referring to “A/T Fluid Change:  in 

Section 5A”.

Water Pump / Generator Drive Belt Tension 
Inspection and Adjustment

S4RS0A1606015

WARNING:

• Disconnect negative cable at battery 

before checking and adjusting belt 
tension.

• To help avoid danger of being burned, do 

not remove radiator cap while engine and 
radiator are still hot. Scalding fluid and 
steam can be blown out under pressure if 
cap is taken off too soon.

 

1) Inspect belt for cracks, cuts, deformation, wear and 

cleanliness. If it is necessary to replace belt, refer to 
“Water Pump / Generator Drive Belt Removal and 
Installation: ”.

2) Check belt for tension. Belt is in proper tension when 

it deflects the following specification under thumb 
pressure (about 10 kg or 22 lb.).

Water pump / generator drive belt tension
“a”: 4.5 – 5.5 mm (0.18 – 0.22 in.) as deflection / 
10 kg (22 lbs)

NOTE:
When replacing belt with a new one, adjust 
belt tension to 3 – 4 mm (0.12 – 0.16 in.).

 

3) If belt is too tight or too loose, adjust it to proper 

tension by displacing generator position.

4) Tighten generator adjusting bolt and pivot bolts as 

specified torque.

Tightening torque
Generator adjusting bolt (a):  23 N·m (2.3 kg-m, 
17.0 lb-ft)
Generator pivot bolt (b):  50 N·m (5.0 kg-m, 36.0 
lb-ft)

5) Connect negative cable at battery.

“a”

I2RH0B160012-

I2RH0B160013-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Бренд: Metra Electronics Страницы: 14
TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Бренд: TATA Motors Страницы: 94
GÄN GA Manual preview
GA
Бренд: GÄN Страницы: 24
Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Бренд: Quadratec Страницы: 20
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Бренд: Ford Страницы: 12
Alpine KCE-G7QI Installation preview
KCE-G7QI
Бренд: Alpine Страницы: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Бренд: Whispbar Страницы: 15
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Бренд: Wagan Страницы: 20
Raptor Series MAGNUM RT Series Manual preview
MAGNUM RT Series
Бренд: Raptor Series Страницы: 6
RAM Ram Dodge 2010 Owner'S Manual preview
Ram Dodge 2010
Бренд: RAM Страницы: 616
Nav TV AUDI-P60H Install Manual preview
AUDI-P60H
Бренд: Nav TV Страницы: 9
Honda Clarity 2018 Owner'S Manual preview
Clarity 2018
Бренд: Honda Страницы: 81
BMW E46/2 Coupe Manual preview
E46/2 Coupe
Бренд: BMW Страницы: 55
Whispbar K496W Fitting Instructions Manual preview
K496W
Бренд: Whispbar Страницы: 15
Honda Sedan CIVIC 2022 Manual preview
Sedan CIVIC 2022
Бренд: Honda Страницы: 701

Бренды по названию

Популярные бренды

Загрузить еще бренды