manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

10C-12 Immobilizer Control System: 

Inspection of Immobilizer Control Module and Its Circuit

S4RS0AA304015

Immobilizer control module and its circuit can be checked at immobilizer control module wiring connector by 
measuring voltage.

CAUTION:

Immobilizer control module cannot be checked by itself. It is strictly prohibited to connect voltmeter or 
ohmmeter to immobilizer control module with connector disconnected from it.

 

Voltage Check

1) Remove immobilizer control module (1) from steering lock assembly referring to “Immobilizer Control Module 

Removal and Installation: ”.

2) Connect immobilizer control module wiring connector (2) to immobilizer control module.
3) Check voltage at each terminal.

NOTE:
As each terminal voltage is affected by the battery voltage, confirm that it is 11 V or more when the 
ignition switch is turned to ON position.

 

1

2

3

4

G24

1

2

I4RS0AA30006-

Connector

Terminal

Circuit

Normal Voltage

Condition

G24

1

BLK/

WHT

Power supply

About 12.0 V

Ignition switch at ON position

0.0 V

Ignition switch at OFF position

2

BLK/

ORG

Ground

0.0 V

Ignition switch at ON position

0.0 V

Ignition switch at OFF position

3

YEL/

BLK

Serial communication line

See the reference 
waveform.

—

0.0 V

Ignition switch at OFF position

4

YEL/

RED

Clock line

See the reference 
waveform.

—

0.0 V

Ignition switch at OFF position

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Eclipse AVN 2210p mkII Operation Manual preview
AVN 2210p mkII
Бренд: Eclipse Страницы: 6
APEXi V-AFC II Instruction Manual preview
V-AFC II
Бренд: APEXi Страницы: 18
Prorack K519 Fitting Instructions For Basic Carrier preview
K519
Бренд: Prorack Страницы: 15
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
EEZ RV 51 SC Instruction Manual preview
51 SC
Бренд: EEZ RV Страницы: 31
Chevrolet LUMINA 1997 Owner'S Manual preview
LUMINA 1997
Бренд: Chevrolet Страницы: 376
Mazda 2008 CX-9 Brochure & Specs preview
2008 CX-9
Бренд: Mazda Страницы: 15
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Бренд: Fast Master Products Страницы: 13
Prorack WHISPBAR S53 Fitting Instructions For Basic Carrier preview
WHISPBAR S53
Бренд: Prorack Страницы: 10
Enduro EM203 User Manual preview
EM203
Бренд: Enduro Страницы: 52
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Бренд: RAM Страницы: 360
ACV 381190-37-1 Installation Manual preview
381190-37-1
Бренд: ACV Страницы: 2
PEUGEOT 5008 2017 Handbook preview
5008 2017
Бренд: PEUGEOT Страницы: 404
Quadratec QuadraTop Adventure Top S Manual preview
QuadraTop Adventure Top S
Бренд: Quadratec Страницы: 13
RAWLINK 36772 Instruction Manual preview
36772
Бренд: RAWLINK Страницы: 25
Baseus CRJS01 User Manual preview
CRJS01
Бренд: Baseus Страницы: 5
Ford B-MAX Quick Reference Manual preview
B-MAX
Бренд: Ford Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды