manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

8B-102 Air Bag System: 

• Poor terminal-to-wire connection.

Check each wire harness in problem circuits for poor 
connection by shaking it by hand lightly. If any 
abnormal condition is found, change the wire harness 
assembly or component parts with new ones.

• Wire insulation which is rubbed through, causing an 

intermittent short as the bare area touches other 
wiring or parts of the vehicle.

• Wire broken inside the insulation. This condition could 

cause a continuity check to show a good circuit, but if 
only 1 or 2 strands of a multi-strand-type wire are 
intact, resistance could be far too high.

Repair and Inspection Required after Accident

S4RS0A8204033

CAUTION:

• All air bag system components, including 

the electrical harness (component 
mounting points), must be inspected after 
an accident. If any components are 
damaged or bent, they must be replaced 
even if air bag system activation did not 
occur.

• Never use air bag system parts from 

another vehicle.

• Do not attempt to service the parts below. 

Service of these parts is by replacement 
only.
– Driver / Passenger air bag (inflator) 

modules

– Driver / Passenger side-air bag (inflator) 

modules

– Driver / Passenger side curtain-air bag 

(inflator) modules

– Driver / Passenger seat belt 

pretensioners

– Forward-sensor
– Driver / Passenger side-sensors
– SDM
– Contact coil and combination switch 

assembly

– Air bag wire harness in main harness, 

instrument panel harness and floor 
harness.

• Proper operation of the sensors and air 

bag system requires that any repairs to the 
vehicle structure return it to its original 
production configuration.

 

CAUTION:

After detecting one time of such collision as 
to meet deployment conditions, the SDM 
must not be used.
Refer to “Air Bag Diagnostic System Check: ” 
when checking the SDM.

 

Accident with Deployment / Activation – Component 
Replacement

When driver and passenger air bags are deployed, the 
following components must be replaced.
• Driver and passenger air bag (inflator) modules
• Driver and passenger seat belt pretensioners
• SDM after detecting such collision as to meet 

deployment conditions

• Forward-sensor
• Instrument panel

(A)

I4RS0A820045-

IYSQ01010028-

IYSQ01820025-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

N-Com B3 User Instructions And Safety preview
B3
Бренд: N-Com Страницы: 28
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Бренд: Gardigo Страницы: 36
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Бренд: IAME Страницы: 17
Saab B205 Installation Instructions Manual preview
B205
Бренд: Saab Страницы: 10
GATmatic TWC-562S Installation, Operation & Maintenance Manual preview
TWC-562S
Бренд: GATmatic Страницы: 13
minnid 1.240.344 Operating Instructions Manual preview
1.240.344
Бренд: minnid Страницы: 44
iArmor EDGE IA-N098 Quick Start Manual preview
EDGE IA-N098
Бренд: iArmor Страницы: 4
Nav TV AUDI A6 Installation Manual preview
AUDI A6
Бренд: Nav TV Страницы: 5
Dodge Ram Commercial2016 Owner'S Manual preview
Ram Commercial2016
Бренд: Dodge Страницы: 675
Brink 4698 Fitting Instructions Manual preview
4698
Бренд: Brink Страницы: 26
SSV Works RG4-DM3 Manual preview
RG4-DM3
Бренд: SSV Works Страницы: 2
Mazda Auto-Dimming Mirror User Manual preview
Auto-Dimming Mirror
Бренд: Mazda Страницы: 2
Audi S4 Biturbo Buyer'S Manual preview
S4 Biturbo
Бренд: Audi Страницы: 9
Curtis 1POLXP1000GS Installation & Owner'S Manual preview
1POLXP1000GS
Бренд: Curtis Страницы: 5
AMP Research BEDXTENDER HD 74805-00A Assembly And Installation Manual preview
BEDXTENDER HD 74805-00A
Бренд: AMP Research Страницы: 7
TEINHOF P-038 Fitting And Operation Manual preview
P-038
Бренд: TEINHOF Страницы: 2
Audi A5 SPORTBACK Owner'S Manual preview
A5 SPORTBACK
Бренд: Audi Страницы: 313
Automotive Data Solutions iDatalink Maestro RR Manual preview
iDatalink Maestro RR
Бренд: Automotive Data Solutions Страницы: 139

Бренды по названию

Популярные бренды

Загрузить еще бренды