Televes OLT 769401 User Manual Download Page 365

Page: 365 / 482

365

Reg. Type

Serial Number

Indicates the ONU serial number

Password (HEX)

Indicates password (Hexadecimal)

Profile

Identifies the ONU profile by ID and name

SW Mode

Indicates the ONU configured software upgrade mode

SW version

Indicates the SW version

Status

Indicates the ONT state

FEC

Indicates if FEC is enabled

OMCI-encr.

Indicates if OMCI encriptation is enabled

Commands

Indicates the available commands for use

Table 7-364: “show” command output table parameters

7.6.17.5.12 “showconfig” command

Name

showconfig

Description

Print the command list that enforces the current configuration

Full path

/remote-eq/discovery/showconfig

Mandatory Parameters

Screen Output

Full command(s) path and used arguments and values to reach the current

configuration.

Table 7-365: “showconfig” command information

/cli/remote-eq/discovery> showconfig ?

Usage SHOWCONFIG:

SHOWCONFIG Print the command list that enforces the current configuration

[OPTIONAL]

--onuID Identifies an ONU by ID, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-403: CLI on line help on “showconfig” command usage in this node context

7.6.17.6 “ONUs” sub-node

This node can be used to configure the remote ONU equipments.

All the commands in this node (and children) always apply to a specific ONU.

When executing each command the identification of the ONU must be provided.

In this sense all commands will have at least three parameters: slot, port, onuID.

If the user does not give those arguments, the command will use the information stored with

/remote-eq/connect

. If there is no information

saved, it will display en error.

If there is information saved with the

connect

command, but the user gives another set of argument values, then the user given values take

precedence over the existing ones.

All the

showconfig

commands will have the three parameters as well.

So, their structure will change (for this node and children only) and be the one depicted below.

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands