Televes OLT 769401 User Manual Download Page 79

Page: 79 / 482

Parameter

Description

Port id

Port identifier

Admin

Port Administrative State

MAC Aging (sec)

Time it takes for a MAC address to be removed from the GPON MAC table, in the case it hasn’t been

received any packet with that source address in that GPON port. This value must be in the range

between 120 and 3600 seconds. (Note: The MAC addresses in the GPON interface are only learnt in

Unicast Unstacked Services)

Distance Minimum/

Maximum

Sets the distance for which the interface can detect ONTs. The difference between the minimum

and the maximum can’t exceed 20km, and the maximum distance can’t be higher than 60km.

BER(sec)

PON port Bit Error Rate in the downstream in sec

Downstream FEC

Flag; Downstream FEC enabled at this PON port if selected

Discover ONTs

Flag; Discover ONTs at this PON port enabled if selected

Table 5-18: GPON interfaces configuration parameters table

5.2.4.5.2 Ethernet Interfaces

In the Ethernet interfaces table it is possible to configure the module Ethernet interfaces.

Figure 5-32: Ethernet interfaces configuration

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands