Televes OLT 769401 User Manual Download Page 426

Page: 426 / 482

Descripción del producto

426

/cli/services> config ?

Usage CONFIG:

CONFIG Configure parameters for a given service. Flags

PPPoE, McFlood, IGMP and DHCP are ignored for Bitstream services.

--serviceID Select an OLT service by ID.

[OPTIONAL]

--add-downlink-ports Add interfaces to the Downlink interface List,

for a given service. (format: slot.port|slot(all) : 3.1,3.5,7)

--add-uplink-lags Add LAG interfaces to the Uplink interface List

for a given service. (format: lagID : 1,2,3)

--add-uplink-ports Add interfaces to the Uplink interface List, for

a given service. (format: slot.port|slot(all) : 3.1,3.5,7)

--admin Administrative State. Enable/disable, in this

context. (enable|disable)

--del-downlink-ports Remove interfaces from the Downlink interface

List, for a given service. (format: slot.port|slot(all) : 3.1,3.5,7)

--del-uplink-lags Remove LAG interfaces from the Uplink interface

List, for a given service. (format: lagID : 1,2,3)

--del-uplink-ports Remove interfaces from the Uplink interface List,

for a given service. (format: slot.port|slot(all) : 3.1,3.5,7)

--dhcp Enable or disable the DHCP relay for a given

service. (enable|disable)

--igmp Enable or disable IGMP for a given service.

(enable|disable)

--mcFlood Multicast flooding. (enable|disable)

--nni-stag Outer VLAN ID (service) on the network-facing

(Ethernet) interface. (1..4094)

--pppoe Enable or disable PPPoE for a given service.

(enable|disable)

--serviceName The Name for the new service. (STRING 31)

--stacked Frame format for the uplink interface. If

enabled, it has two VLAN tags, otherwise only one VLAN tag. (enable|disable)

--type Identifies the type of service. (unicast|multicast

|bitstream|univoip|mac bridge)

--uni-ctag VLAN ID delivered/received from the (Ethernet)

subscriber-facing interface at the ONU. (1..4094)

Figure 7-527: CLI on line help on “config” command usage in this node context

7.6.19.3 “create” command

Name

create

Description

Create a new network service.

Full path

/services/create

Mandatory Parameters

--nni-stag
--serviceName
--type
--uni-ctag

Screen Output

Table 7-: “create” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands