Televes OLT 769401 User Manual Download Page 416

Page: 416 / 482

Descripción del producto

416

/cli/routing/ping> create ?

Usage CREATE:

CREATE Create a new ping session.

--ip-address IPv4 address

[OPTIONAL]

--probe-count Number of probes to send. (1..15)

--probe-interval Interval (in seconds) between each probe.

(1..60)

--probe-size Probe size. (0..65507)

Figure 7-502: CLI on line help on “create” command usage in this node context

7.6.18.3.2 “remove” command

Name

remove

Description

Remove an existing ping session

Full path

/routing/ping/remove

Mandatory Parameters

-ID

Screen Output

Table 7-467: “remove” command information

/cli/routing/ping> remove ?

Usage REMOVE:

REMOVE Remove an existing ping session.

--ID Identifies a table entry by ID, in this context.

Figure 7-503: CLI on line help on “remove” command usage in this node context

7.6.18.3.3 “show” command

Name

show

Description

Show the current ping sessions configuration

Full path

/routing/ping/show

Mandatory Parameters

No mandatory parameters

Screen Output

Table, Figure 7-505. Table parameters description in Table 7-469.-.

Table 7-468: “show” command information

/cli/routing/ping> show ?

Usage SHOW:

SHOW Show the current ping sessions configuration

[OPTIONAL]

--ID Identifies a table entry by ID, in this context.

Figure 7-504: CLI on line help on “show” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands