Televes OLT 769401 User Manual Download Page 245

Page: 245 / 482

245

/cli/erp-ring> config ?

Usage CONFIG:

CONFIG Configure an existing ERP instance.

--ID Identifies a table entry by ID, in this context.

[OPTIONAL]

--add-vlan Add one Protected vlan entry to the list (1..4094)

--admin Administrative State. Enable/disable, in this

context. (enable|disable)

--aps-ch-vlan Set the APS channel VLAN (1..4094)

--aps-meg-level Set APS channel MEG level value (0..7) min

--del-vlan Delete one Protected vlan entry from the list

(1..4094)

--guard-time Set the guard time (1..200) x10ms

--holdoff-time Set the hold off time, in hundreds of milliseconds

(0..100) x100ms

--open-ring Specify whether the ring is open or not.

(enable|disable)

--p0-cfm-probe-id Identify a CFM probe by ID (0 for none)

--p0-port Identify a Port (e.g.: eth.1, pon.3, lag.2)

--p0-slot Identify a Slot (not used for LAG)

--p0-type Set the port type (non-rpl|rpl|rpl-neighbor)

--p1-cfm-probe-id Identify a CFM probe by ID (0 for none)

--p1-port Identify a Port (e.g.: eth.1, pon.3, lag.2)

--p1-slot Identify a Slot (not used for LAG)

--p1-type Set the port type (non-rpl|rpl|rpl-neighbor)

--revertive Specify is reversion is enabled. (enable|disable)

--ring-id Set the ring ID

--wtr Set the Wait to Restore time (1..12) x10ms

Figure 7-141: CLI on line help on “config” command usage in this node context

7.6.7.2 “create” command

Name

create

Description

Create a new Ethernet Ring Protection (ERP) instance.

Full path

/erp-ring/create

Mandatory Parameters

Screen Output

Table 7-117: “create” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands