Televes OLT 769401 User Manual Download Page 441

Page: 441 / 482

441

/cli/synchronism/global> config ?

Usage:

CONFIG Configure synchronism global parameters

[OPTIONAL]

--free-run-source Activate or deactivate the free-run source (enable|disable)

--holdover-msg-delay

Set the Holdover message delay (500..2000 ms)

--min-quality-before-squelch

Set the Minimum quality before squelch

--quality-level-mode

Enables synchronism quality level (enable|disable)

--reversibility-level-mode Enables revertive switching mode when recovering

from a failure (enable|disable)

--reversibility-time

Set the Reversibility time (0..3600 sec.)

--send-val-after-quality-unknown Set the value to be sent in case Quality Unknown

is received

--switching-msg-delay

Set the Switching message delay (180..500 ms)

Figure 7-: CLI on line help on “config” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands