Televes OLT 769401 User Manual Download Page 418

Page: 418 / 482

Descripción del producto

418

Figure 7-508: Output of ”status” command with no arguments in this node context”

Parameter

Description

Table entry identifier

Active

Flag; enabled if probe active.

Probes

Send:

Number of sent packets.

Success:

Number of received packets.

Fail:

Number of failled packets.

Round trip time (us)

Min:

Minimum observed Round trip time

Avg:

Average observed Round trip time

Max:

Maximum observed Round trip time

Table 7-472: “status” command output table parameters

7.6.18.4 “route-table” sub-node

7.6.18.4.1 “config” command

Name

config

Description

Configure an existing static route by ID.

Full path

/routing/route-table/config

Mandatory Parameters

--ID

Screen Output

Table 7-473: “config” command information

/cli/routing> route-table/config ?

Usage CONFIG:

CONFIG Configure an existing static route by ID.

--ID Identifies a table entry by ID, in this context.

[OPTIONAL]

--admin Administrative State. Enable/disable, in this

context. (enable|disable)

--dst-ip-addr Destination IP address.

--dst-ip-mask Destination IP mask.

--gw-ip-addr Gateway IP address.

--preference Route preference.

Figure 7-509: CLI on line help on “config” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands