Televes OLT 769401 User Manual Download Page 82

Page: 82 / 482

Descripción del producto

5.2.4.7 Services

The services window is used to configure general OLT services giving an end-to-end perspective by configuring the service VLAN in the uplink

interface and the VLAN delivered in the ONU port. This window has two tables: Rate limiters configuration table and Services table, Figure 5-35

In CLI, OLT services related commands including configuration are described in section 7.6.19 “services” node and subsections.

Figure 5-35: OLT services configuration window

Parameter

Description

Broadcast (bps)

Rate Limiter configured value for Broadcast services

Multicast (bps)

Rate Limiter configured value for Multicast services

Unknown Unicast (bps)

Rate Limiter configured value for Unknown Unicast services

Table 5-22: Rate Limiters table Configuration parameters

Parameter

Description

Name

Name that identifies the Service

Admin

Service Administrative State

Stacked

Provides the frame format in the uplink interface. If it’s Stacked the frame contains two vlan tags, if it’s

Unstacked the frame contains only one vlan tag. Both vlans have Ethertype=0x8100.

Type

Identifies the type of service:

Unicast

: Bidirectional service, where each frame has only one final destination. These services are

used in Residential applications, where some kinds of packets can be trapped and processed (ex.

DHCP, IGMP). In case of Unstacked Services, MAC Learning is preformed.

Multicast

: Unidirectional Service, where one frame can be delivered to several destinations. These

destinations are controlled by IGMP Snooping/Proxy.

UniVoIP

: Bidirectional Service, where each frame has only one final destination. Similar to

Unicast Services, with the difference that when it’s configured to the ONU, VoIP configurations are

downloaded to the ONT.

Bitstream

: Bidirectional Service, where each frame has only one final destination. These services are

used in Business applications, where all packets pass transparently by the system and MAC learning

is disabled.

MAC Bridge:

In this type of service forwarding is based on S-VID+DMAC or S-VID+C-VID+DMAC.

Unicast Unknown, Multicast and Broadcast MAC Addresses are replicated to all the GEM Ports that

belong to the same S-VID or S-VID+C-VID

Ethernet/LAG

Identifies the uplink physical (ETH) or logical (LAG) port

NNI S-TAG

Identifies the outer tag of the service used in the uplink port

PON/Slot

Identifies the GPON port(s) associated to the Service

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands