Televes OLT 769401 User Manual Download Page 313

Page: 313 / 482

313

/cli/ip-source-guard> config ?

Usage CONFIG:

CONFIG Configure IP Source Guard parameters.

--ID Identifies a table entry by ID, in this context.

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--ip-address IPv4/IPv6 address

--mac Identify/Set a MAC entry, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

--serviceID Select an OLT service by ID.

Figure 7-288: CLI on line help on “config” command usage in this node context

7.6.12.2 “create” command

Name

create

Description

Create a new IP Source Guard entry.

Full path

/ip-source-guard/create

Mandatory Parameters

Screen Output

Table 7-257: “create” command information

/cli/ip-source-guard> create ?

Usage CREATE:

CREATE Create a new IP Source Guard entry.

[OPTIONAL]

--ID Identifies a table entry by ID, in this context.

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--ip-address IPv4/IPv6 address

--mac Identify/Set a MAC entry, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

--serviceID Select an OLT service by ID.

Figure 7-289: CLI on line help on “create” command usage in this node context

7.6.12.3 “remove” command

This command deletes the IP route. There can only be one IP route.

Name

remove

Description

Remove an existing IP Source Guard entry.

Full path

/ip-source-guard/remove

Mandatory Parameters

--ID

Screen Output

Table 7-258: “remove” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands