Televes OLT 769401 User Manual Download Page 421

Page: 421 / 482

421

/cli/routing/route-table> status ?

Usage STATUS:

STATUS Show the current route-table status

Figure 7-515: CLI on line help on “status” command usage in this node contex

Figure 7-516: Output of ”status” command in this node context”

Parameter

Description

(ID) Routing Interface

Routing interface identifier

Protocol

Used protocol identifier

Update time

Route update time

Destination IP Address

Route Destination IP Address

Destination IP Mask

Route Destination IP Mask

Gateway IP Addr

Route used Gateway IP Address

Preference

Route Preference

Metric

Route Metric (number of hops)

Table 7-480: “status” command - output table parameters

7.6.18.5 “traceroute” sub-node

7.6.18.5.1 “create” command

Name

create

Description

Create a new traceroute session.

Full path

/routing/traceroute /create

Mandatory Parameters

--ip-address

Screen Output

Table 7-481: “create” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands