Televes OLT 769401 User Manual Download Page 145

Page: 145 / 482

145

The Ethernet Interfaces Status table, Figure 6-14, is composed by the following parameters:

Parameter

Description

Eth Id

Ethernet Interface identifier

High Layer

Indicates to each LAG (in case the port is a LAG member) the port belongs to

Admin

Ethernet port Administrative State

Auto-Negotiation

If the port is configured to Auto negotiation, indicates the Auto Negotiation State

Media Type

Indicates the Link Speed

Collisions

Not applicable in Full Duplex interfaces

Status

It’s composed by the following columns:

Link:

Indicates the Link State

Tx:

Indicates if the interface is transmitting packets

: Indicates if the interface is receiving packets

Statistics

By pressing view, a window with the port statistics according with RFC2819 will open,

Figure 6-. Differential and absolute values’ statistics are available.

Table 6-13: Ethernet Interfaces Status parameters table

Figure 6-16: Ethernet Port Statistics

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands