Televes OLT 769401 User Manual Download Page 376

Page: 376 / 482

Descripción del producto

376

Parameter

Description

ONU Port

Identifies an ONU port by ID

Enable

Flag; indicates if the port is enabled.

Input TPID

Identifies input VLAN tag

Output TPID

Indicates output VLAN tag

(ID)

DSCP to PBIT profile identifier (Number)

DSCP to PBIT profile

Indicates DSCP to PBIT profile bit mapping

Table 7-385: “show” command output table parameters

7.6.17.6.6.3 “showconfig” command

Name

showconfig

Description

Print the command list that enforces the current configuration

Full path

/cli/remote-eq/onu/ext-vlan-tag-op/showconfig

Mandatory Parameters

Screen Output

Full command(s) path and used arguments and values to reach the current

configuration.

Table 7-386: “showconfig” command information

/cli/remote-eq/onu/ext-vlan-tag-op> showconfig ?

Usage:

SHOWCONFIG Print the command list that enforces the current configuration

[OPTIONAL]

--onuID Identifies an ONU by ID, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-426: CLI on line help on “showconfig” command usage in this node contex

7.6.17.6.6.4 “operation-table” sub-node

7.6.17.6.6.4.1 “config” command

Name

config

Description

Configure an Extended VLAN Tagging Operation Table entry

Full path

/remote-eq/onu/ext-vlan-tag-op/operation-table/config

Mandatory Parameters

--ID
--onu-port

Screen Output

Table 7-387: “config” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands