Televes OLT 769401 User Manual Download Page 457

Page: 457 / 482

457

7.6.20.3.1.3.2 “show” command

Name

show

Description

Show the status information

Full path

/synchronism/status/global/sources/show

Mandatory Parameters

This command has no parameters.

Screen Output

Table, Figure 7-587. Table parameters description in Table 7-549

Table 7-548: “show” command information

/cli/synchronism/status/global/sources> show ?

Usage:

SHOW Show the status information.

Figure 7-586: CLI on line help on “show” command usage in this node context

Figure 7-587: Output of ”show” command in this node context

Parameter

Description

Indicates synchronization source

Source

Indicates synchronization source (slot or junction number)

SSM Rx

This column identifies the received SSM (Synchronization Status Message);

SSM Used

This column identifies the used SSM

Signal Fail

Signal failure of the respective synchronism source

Attenuation

Attenuation (measured in dB) associated with each of the existing synchronism

junctions

Table 7-549: “show” command output table parameters

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands