Televes OLT 769401 User Manual Download Page 194

Page: 194 / 482

Descripción del producto

194

Mandatory Parameters

--acl-id
--port

Screen Output

Table 7-12: “config” command information

/cli/acl/interface> config ?

Usage:

CONFIG Configure an existing Interface association.

--acl-id Identifies an ACL by ID, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context. (enable|disable)

--direction Identifies an ACL Rule by ID, in this context.

Figure 7-30: CLI on line help on “config” command usage in this node context

7.6.1.6.3 “remove” command

Name

remove

Description

Remove an existing Interface association..

Full path

/acl/interface/remove

Mandatory Parameters

--acl-id
--port

Screen Output

Table 7-13: “remove” command information

/cli/acl/interface> remove ?

Usage:

REMOVE Remove an existing Interface association

--acl-id Identifies an ACL by ID, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-31: CLI on line help on “remove” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands