Televes OLT 769401 User Manual Download Page 442

Page: 442 / 482

Descripción del producto

442

7.6.20.1.2 “show” command

Name

show

Description

Show the current services configuration. If a service ID is given shows all the

downlink ports.

Full path

/synchronism/global/show

Mandatory Parameters

This command has no parameters

Screen Output

Tables Figure 7-557. Table parameters description in Table 7-519

Table 7-518: “show” command information

/cli/synchronism/global> show ?

Usage:

SHOW Show the current configuration

Figure 7-556: CLI on line help on “show” command usage in this node context

Figure 7-: Output of ”show” command in this node context

Parameter

Description

Quality level-mode

Configured Synchronism quality level. If enabled the user can set the

equipment synchronization to take into account the SSM synchronization

sources (Synchronization Status Message)

Reversilibity-level-Mode

Configured reversal switching mode when recovering from a failure.
If Enabled: the status machine of the equipment only considers for

synchronization source, a source that does not show timing flaws and where the

Reversibility Time has expired. If the quality/priority of this source (depending

on the current configuration of the Quality Level Mode) is higher than the

current source, the equipment will use this quality/priority source. Otherwise

the source is not changed.
If Disabled: a source that has been previously considered invalid will only be

used for synchronization, if the current source fails and if there is no other

source with a higher quality/priority

Reversibility-time (s)

Configured reversibility time - time, in seconds: after this period of time, the

fault condition disappears and the invalid source will be reconsidered for

synchronization. This time is considered after the Wait-To-Restore time has

elapsed

Holdover-message delay (ms)

Configured Holdover message delay - time, in milliseconds, considered in the

case where the equipment is in Holdover mode. This state is due to a fault

condition in the selected synchronization source and when there is no other

available source.

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands