Televes OLT 769401 User Manual Download Page 73

Page: 73 / 482

Figure 5-25: Synchronism configuration sub-menu

In CLI, Synchronism node and sub-nodes as well as related commands including Configuration are described in section 7.6.20 “synchronism” node

and sub-sections.

5.2.4.4.1 Global

The system can synchronize the output frequency with one of two distinct references.

The tables of the following figures allow setting global synchronization parameters, as well as the system synchronization source (e.g. Eth

interface), or in free run mode.

Figure 5-26: Synchronism Configuration Window- Synchronism table

Parameter

Description

Quality Level Mode

Enabled

: the user can set the equipment synchronization to take into account the SSM synchronization

sources (Synchronization Status Message)

Disabled

: the device ignores the SSM synchronization source.

Reversibility level

mode

Enabled:

the status machine of the equipment only considers for synchronization source, a source that

does not show timing flaws and where the Reversibility Time has expired. If the quality/priority of this

source (depending on the current configuration of the Quality Level Mode) is higher than the current

source, the equipment will use this quality/priority source. Otherwise the source is not changed.

Disabled:

a source that has been previously considered invalid will only be used for synchronization, if

the current source fails and if there is no other source with a higher quality/priority

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands