Televes OLT 769401 User Manual Download Page 435

Page: 435 / 482

435

Parameter

Description

Service (ID) Name

Service identified by Service ID (number) and Service Name with active counters

gathering service statistics

Slot

Slot number where is the port with the service available

Port

Port number where the service is available.

Table 7-506: “show-active” command output table

7.6.19.8.1.4 “start” command

Name

start

Description

Start the statistics counter for a given interface and service.

Full path

/services/statistics/counters/start

Mandatory Parameters

--serviceID

Screen Output

Table 7-507: “start” command information

/cli/services/statistics/counters> start ?

Usage:

START Start the statistics counter for a given interface and service.

--serviceID

Select an OLT service by ID.

[OPTIONAL]

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-544: CLI on line help on “start” command usage in this node context

7.6.19.8.1.5 “stop” command

Name

stop

Description

Stop an active statistics counter.

Full path

/services/statistics/counters/stop

Mandatory Parameters

--serviceID

Screen Output

Table 7-508: “stop” command information

/cli/services/statistics/counters> stop ?

Usage:

STOP Stop an active statistics counter.

--serviceID

Select an OLT service by ID.

[OPTIONAL]

--port

Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

Figure 7-545: CLI on line help on “stop” command usage in this node contex

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands