Televes OLT 769401 User Manual Download Page 282

Page: 282 / 482

Descripción del producto

282

/cli/interfaces/gpon> showconfig ?

Usage:

SHOWCONFIG Print the command list that enforces the current configuration

Figure 7-217: CLI on line help on “showconfig” command usage in this node context

7.6.10.2 “gpon” sub-node

7.6.10.2.1 “config” command

Name

config

Description

Configure the given PON interfaces.

Full path

/interfaces/gpon/config

Mandatory Parameters

--port

Screen Output

Table 7-192: “config” command information

/cli/interfaces/gpon> config ?

Usage CONFIG:

CONFIG Configure the given PON interfaces.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context.

(enable|disable)

--ber Bit Error Rate (BER) Interval according to G.984.3. Value in

seconds. (1..3600 s)

--fec-downstream Forward Error Correction (FEC) on the Downstream side.

(enable|disable)

--ip-source-guard Enable/Disable IP Source Guard filtering for the specified

interface. (enable|disable)

--mac-agging Time it takes for a MAC address to be removed from the GPON MAC

table. Value in seconds. (120..3600 s)

--mapping-mode Specify the mapping mode to be applied to GPON interface.

Defaults to VLAN. (VLAN|VLAN+PBITS)

--max-distance Sets the maximum distance in Km for which the interface can

detect ONUs (20..60 Km)

--min-distance Sets the minimum distance in Km for which the interface can

detect ONUs.(0..40 Km)

--onu-auto-discovery New ONUs are automatically added to the discovery table for a

given PON interface. (enable|disable)

Figure 7-218: CLI on line help on “config” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands