Televes OLT 769401 User Manual Download Page 146

Page: 146 / 482

Descripción del producto

146

The Ethernet Port Statistics table is composed by the following parameters:

Parameter

Description

Drop Events

Number of dropped packets

Octets

Number of bytes

Packets

Number of Packets

Broadcast Packets

Number of Broadcast Packets

Multicast Packets

Number of Multicast Packets

Alignment of CRC Errors

Number of packets with wrong FCS (Frame Check Sequence)

Undersize Packets

Number of packets with size less than 64 bytes

Oversize Packets

Number of packets with size over than 1518 bytes

Fragments

Number of packets with size less than 64 bytes and with wrong FCS (Frame Check

Sequence)

Jabbers

Number of packets with size over than 1518 bytes and with wrong FCS (Frame Check

Sequence)

Collisions

Number of collisions in the Ethernet Segment (only in Half Duplex)

Packets with 64 Octets

Number of 64 bytes packets

Packets with 65 to127 Octets

Number of packets with size between 65 to 127 bytes

Packets with 128 to 255 Octets

Number of packets with size between 128 to 255 bytes

Packets with 256 to 511 Octets

Number of packets with size between 256 to 511 bytes

Packets with 512 to 1023 Octets

Number of packets with size between 512 to 1023 bytes

Packets with 1024 to 1518

Octets

Number of packets with size between 1024 to 1518 bytes

Throughput (bps)

Indicates approximately the received and transmitted bit rate (1Mbit/s Granularity)

Table 6-14: Ethernet Port Statistics parameters table

6.2.4 LAG Interfaces

The selection of Status menu item LAG Interfaces opens a LAG interfaces Status window, Figure 6-17, where it is possible to check

the LAG and each LAG member status.

Figure 6-17: LAG interfaces status

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands