Televes OLT 769401 User Manual Download Page 321

Page: 321 / 482

321

7.6.14.4.2.2 ”show” command

Name

show

Description

Show the Switch MAC Table.

Full path

/mac-table/status/switch/show

Mandatory Parameters

Screen Output

Table Figure 7-309. Table parameters description in Table 7-274

Table 7-273: “show” command information

cli/mac-table/status> switch/show ?

Usage SHOW:

SHOW Show the Switch MAC Table. If no slot is provided, the MACs will be

read on the active switch fabric slot.

[OPTIONAL]

--mac Identify/Set a MAC entry, in this context.

--port Identifies an interface on the OLT. (e.g.: pon.2; eth.3; lag.1)

--serviceID Select an OLT service by ID.

--vlan Choose a VLAN ID.

Figure 7-308: CLI on line help on “show” command usage in this node context

Figure 7-309: Output of ”show” command in this node context

Parameter

Description

Slot

Indicates the Slot

Port

Indicates the Port

ONT ID

Indicates the ONT identifier

(ID) OLT Service

Indicates the service identifier (ID) and name

VLAN

Indicates the used VLAN

MAC

Indicates the learned MAC address

Table 7-274: “show” command output table parameters

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands