Televes OLT 769401 User Manual Download Page 446

Page: 446 / 482

Descripción del producto

446

Figure 7-563: Output of ”show” command in this node context

Parameter

Description

Table entry Identifier

Source

Lists all possible interfaces (slots and junctions) for synchronization

Active

Allows a given synchronization source to be enabled or disabled.

Interface

This column allows selection of an n Ethernet interface, within a certain module, which

can be used as a possible synchronization source. In the case of the junctions, it is

possible to configure if this operates at 2MHz or 2Mbits

Priority

Allows setting the source priority. The lower the priority value, the greater the

preference of this source over the others. Note that, for sources having equal priority,

the concept of reversibility has no meaning.

QL-SSM

Quality Level; The user can select the intended SSM value for the source. This value

overrides the value received by the equipment. When the SSM value is overridden, the

following precautions should be taken: In case of interface LOS, this source is not used.

If the received value is DNU, the equipment will continue to use this synchronization

source.

SA-bit-Tx

Allows setting the value of the transmission Sa bit in the case of 2Mbps (only for the

synchronization junctions);

SA-bit-Rx

Allows setting the value of the reception Sa bit in the case of 2Mbps (only for the

synchronization junctions)

Hold-Off time (ms)

The Hold-Off time ensures that the activation, even if short, of the signal failure has

no influence on the synchronization source selection process. This value can vary

between 300ms and 1800ms

Wait-To-Restore time (min)

The Wait-To-Restore time ensures that a prior fault in the synchronization source will

only be considered valid for this selection process if it is maintained without failure

for a specified period of time. This parameter can have values ranging from 0 to 12

minutes with 1 minute resolution. The default value is 5 minutes.

Table 7-: “show” command output table parameters

7.6.20.1.5 “showconfig” command

Name

showconfig

Description

Print the command list that enforces the current configuration

Full path

/synchronism/global/sources/showconfig

Mandatory Parameters

This command has no parameters

Screen Output

Full command(s) path and used arguments and values to reach the current

configuration.

Table 7-526: “showconfig” command information

/cli/synchronism/globa/sourcesl> showconfig ?

Usage:

SHOWCONFIG Print the command list that enforces the current configuration

Figure 7-564: CLI on line help on “showconfig” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands