Televes OLT 769401 User Manual Download Page 198

Page: 198 / 482

Descripción del producto

198

/cli/acl/rule-ipv4-ext> config ?

Usage:

CONFIG Configure an existing IPv4 Extended Rule.

--acl-id Identifies an ACL by ID, in this context.

--rule-id Identifies an ACL Rule by ID, in this context.

[OPTIONAL]

--action permit or deny

--admin Administrative State. Enable/disable, in this context. (enable|disable)

--dscp Match the DSCP value. (not-used|0..63)

--dst-ipv4-addr Destination IPv4 Address

--dst-ipv4-mask Destination IPv4 Mask

--dst-port-end Specify Destination L4 port number (not-used|0..65535)

--dst-port-start Specify Destination L4 port number (not-used|0..65535)

--name Set a name for a specific Rule (STRING 31)

--precedence Match IP precedence value (not-used|0..7)

--protocol Match the protocol number. Protocol field of the IPv4 header. (not-

used|0..255)

--src-ipv4-addr Source IPv4 Address

--src-ipv4-mask Source IPv4 Mask

--src-port-end Specify Source L4 port number (not-used|0..65535)

--src-port-start Specify Source L4 port number (not-used|0..65535)

--tos Specify match condition based on IP TOS Mask value. Two-digit

hexadecimal number (0000..0XFF)

--tos-mask Specify match condition based on IP TOS value. Two-digit hexadecimal

number (0000..0XFF)

Figure 7-37: CLI on line help on “config” command usage in this node context

7.6.1.9.2 “create” command

Name

Create

Description

Create a new IPv4 Extended Rule for a given ACL ID.

Full path

/acl/rule-ipv4-ext/create

Mandatory Parameters

--acl-id
--action

Screen Output

Table 7-20: “create” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands