Televes OLT 769401 User Manual Download Page 46

Page: 46 / 482

Descripción del producto

3.11.1 OLT Ref.769401 single board

This board integrates the OLT Ref.769401 switch fabric, uplink ports and GPON ports. It provides the Operation and Maintenance function of the

system, and it also switches the client traffic between the client and the uplink interfaces.

OLT Ref.769401 single board has a 64 Gbps switching capacity and in addition has four 10GbE internal connections and one O&M for each of the

uplink and client interfaces.

3.11.1.1 Interfaces

2x ETH management interfaces G1 and G2 (RJ45);

1xUSB debug port, exclusively for factory configuration

1x MISC (Alarms/conditions and ACK indicators) contacts

4 x 10GE uplink interfaces

SFP+ modules

4 x 1GbE uplink interfaces

SFP modules

8x GPON interfaces

SFP modules

3.11.1.2 LED Indicators

The board provides 2 LEDs, named PRC, ON, that must indicate

PRC: stands for the word «Processing» and defines the overall state of the board:

If Led is either OFF or steady GREEN the board has an internal hardware malfuction that does not allow the board to boot

If Led blinks GREEN 1 time per second the board is active;

If Led blinks GREEN 3 times per second the board is inactive;

ON: reflects the state of the -48VDC power supplies (A and B):

Steady green if rail A and B are OK;

Blinking GREEN/RED if rail A is NOT OK and rail B is OK;

Double GREEN/RED blinking if rail A is OK and rail B is NOT OK;

3.11.1.3 Interface Interconnection Cables

The equipment has two Ethernet (G1 and G2) management interfaces. For the G1 and G2 interfaces, UTP network cable category 5e or higher with

RJ45 connectors should be used as interconnection cable. The expected range with this interconnection cable is 100m maximum.

For the MISC interface a coaxial Metral 2mm (FCI TM) plug is used.

The USB debug port is exclusively for factory configuration.

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands