Televes OLT 769401 User Manual Download Page 445

Page: 445 / 482

445

7.6.20.1.4.2 “config” command

Name

config

Description

Configure synchronism sources information.

Full path

/synchronism/sources/config

Mandatory Parameters

--ID

Screen Output

Table 7-523: “config” command information

/cli/synchronism/global/sources> config ?

Usage:

CONFIG Configure synchronism sources information.

--ID

Identifies a table entry by ID, in this context.

[OPTIONAL]

--QL-SSM Set the Quality-Level for this particular clock source

--active Enables clock source activation (enable|disable)

--hold-off-time If a source goes down, wait ‘n’ (ms) before removing it from the clock

selection (300..1800 ms)

--interface

Set the interface of the card to be used as clock source.

availableValues)

--priority Set the clock source priority value (1..253)

--sa-bit-RX

Configure SA bit used for reception of SSM packets(4..8)

--sa-bit-TX

Configure SA bit used for transmission of SSM packets(4..8)

--wait-to-restore Amount of time before including a new clock source in clock selection

(0..12 min.)

Figure 7-561: CLI on line help on “config” command usage in this node context

7.6.20.1.4.3 “show” command

Name

show

Description

Show the current services configuration. If a service ID is given shows all the

downlink ports.

Full path

/synchronism/global/show

Mandatory Parameters

This command has no parameters

Screen Output

Tables Figure 7-563.Table parameters description in Table 7-525

Table 7-524: “show” command information

/cli/synchronism/global/sources> show ?

Usage:

SHOW Show the current sources configuration

Figure 7-562: CLI on line help on “show” command usage in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands