Televes OLT 769401 User Manual Download Page 413

Page: 413 / 482

413

Figure 7-495: Output of ”status” command in this node context

Parameter

Description

(ID) Routing Interface

Routing Interface identificatier

IP Address

IP address of the system for ARP mapping.

MAC Adress

MAC address of the system mapped to the IP address.

Type

Type of ARP entry (LOCAL|Dynamic)

Age

Aging time.tiem during which the MAC Address is active.

Table 7-459: Status command – output table parameters

7.6.18.2 “ipv4-interface” sub-node

7.6.18.2.1 “config” command

Name

config

Description

Configure parameters for an IPv4 routing interface

Full path

/routing/ipv4-interface/config

Mandatory Parameters

--ID

Screen Output

Table 7-460: “config” command information

/cli/routing/ipv4-interface> config ?

Usage CONFIG:

CONFIG Configure

--ID Identifies a table entry by ID, in this context.

[OPTIONAL]

--admin Administrative State. Enable/disable, in this

context. (enable|disable)

--ip-address IPv4 address

--mtu Interface MTU [68 - 9198].

--name IP interface name. (STRING 31)

--serviceID Select an OLT service by ID.

--subnet-mask IPv4 Subnet Mask

Figure 7-496: CLI on line help on “config” command usage in this node context

7.6.18.2.2 “create” command

Name

create

Description

Create a new entity.

Full path

/routing/ipv4-interface/create

Mandatory Parameters

--serviceID

Screen Output

Table 7-461: “create” command information

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands