Televes OLT 769401 User Manual Download Page 204

Page: 204 / 482

Descripción del producto

204

/cli/acl/rule-ipv6-ext> create ?

Usage:

CREATE Create a new IPv6 Extended Rule for a given ACL ID.

--acl-id Identifies an ACL by ID, in this context.

--action permit or deny

[OPTIONAL]

--admin Administrative State. Enable/disable, in this context. (enable|disable)

--dscp Match the DSCP value. (not-used|0..63)

--dst-ipv6-addr Destination IPv6 Address

--dst-ipv6-prefix Destination IPv6 prefix length (0..128)

--dst-port-end Specify Destination L4 port number (not-used|0..65535)

--dst-port-start Specify Destination L4 port number (not-used|0..65535)

--flow-label Match IPv6 flow label field (not-used|0..1048575)

--name Set a name for a specific Rule (STRING 31)

--protocol Match the protocol number. Protocol field of the IPv4 header. (not-

used|0..255)

--rule-id Identifies an ACL Rule by ID, in this context.

--src-ipv6-addr Source IPv6 Address

--src-ipv6-prefix Source IPv6 prefix length (0..128)

--src-port-end Specify Source L4 port number (not-used|0..65535)

--src-port-start Specify Source L4 port number (not-used|0..65535)

Figure 7-46: CLI on line help on “create” command usage in this node context

7.6.1.11.3 “show” command

Name

show

Description

Show the current IPv6 Extended Rules configured.

Full path

/acl/rule-ipv6-ext/show

Mandatory Parameters

No mandatory parameters

Screen Output

Table Figure 7-48; Table parameters are described in Table 7-30.

Table 7-29: “show” command information

/cli/acl/rule-ipv6-ext> show ?

Usage:

SHOW Show the current IPv6 Extended Rules configured.

[OPTIONAL]

--acl-id Identifies an ACL by ID, in this context.

Figure 7-47: CLI on line help on “show” command usage in this node context

Figure 7-48: Output of ”show” command without arguments in this node context

Summary of Contents for OLT 769401



































































































































































































































































































































































































































































































Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands

Televes OLT 769401, User Manual

Search results

Summary of Contents for OLT 769401

Reviews:

Related manuals for OLT 769401

Brands by name

Popular brands